Access Official Technical PDF

Share Summary:LinkedInEmail

Choosing a fixed gas detector for an industrial site involves more than selecting the gas to measure. Engineers and plant teams also need to consider sensor technology, control-system connections, hazardous-area requirements, installation conditions and the practicalities of inspection and maintenance. The Sensepoint XCD range is designed to monitor flammable gases, selected toxic gases and oxygen in potentially explosive atmospheres, indoors or outdoors.

Its common transmitter platform combines a local display and configurable outputs with sensor options for different gas hazards. Understanding how those elements fit together helps teams assess whether a detector configuration suits a new installation or retrofit.

Fixed gas detector options for different hazards

Sensepoint XCD uses three transmitter types to support different sensor families. The mV transmitter works with catalytic and infrared (IR) sensors for flammable gases, as well as an IR carbon dioxide sensor. The electrochemical, or EC, transmitter supports sensors for hydrogen sulphide (H2S), carbon monoxide (CO), hydrogen (H2) and nitrogen dioxide (NO2). A separate transmitter is used for oxygen detection.

Available configurations include catalytic detection of flammable gases, IR detection linearised to methane or propane, and IR carbon dioxide detection. The specified flammable ranges extend to 0–100% of the lower explosive limit (LEL), while the IR carbon dioxide sensor has a 0–2% by volume range. Toxic-gas ranges vary by sensor; for example, the listed H2S range is user-selectable from 10 to 100 ppm. Oxygen detection uses a fixed 25% by volume full-scale range.

The transmitter can recognise sensors within its compatible family. The sensor plugs into the transmitter, which configures itself for that sensor. This arrangement gives a project team a choice of detection technologies while retaining a shared transmitter approach.

Clear status and configurable control-system outputs

A tri-colour, backlit LCD communicates detector status at a glance. A steady green display indicates normal operation, flashing yellow indicates a fault or warning, and flashing red indicates an alarm. The display also provides digits, a bar graph and icons, supporting local checks where the detector is installed or when several units are present in an area.

For connection to plant control systems, the detector provides a selectable sink or source 4–20 mA output and three programmable relays: two alarm relays and one fault relay. MODBUS RTU over RS485 is available as an option. The relays can be configured, and settings such as measurement range, alarm set points and the detector’s electronic tag can be adjusted using the LCD and magnetic switches.

During configuration, the outputs are automatically inhibited. This is intended to reduce the risk of a false alarm being sent to the control panel while maintenance or adjustment is under way. Integrators should account for this operating behaviour when defining procedures and control-system responses.

Installation in hazardous and outdoor environments

The transmitter has an integral mounting plate for surface installation. With an optional bracket, it can also be mounted on a horizontal or vertical pipe or structure within the dimensions specified for the installation. The enclosure is available in epoxy-painted aluminium alloy or 316 stainless steel, and the detector has an IP66 rating. Cable or conduit entry arrangements depend on the certification version: the listed configurations use two M20 entries or two ¾-inch NPT entries.

Electrical installation should follow applicable national guidance and use suitably mechanically protected cable, glands or conduit. The specified supply range depends on certification version: 16–32 VDC for ATEX/IECEx/AP versions and 12–32 VDC for UL/CSA versions, with 24 VDC nominal. Cable size should be selected to maintain the required operating voltage at the detector over the installed cable length. The product documentation also advises terminating the cable screen at the detector or controller, not both.

Accessories are available for particular mounting or environmental needs, including a sunshade/deluge protection assembly, duct mounting kit, collecting cone and calibration gas flow housing. A suitable blanking plug must seal any unused entry to maintain the enclosure’s IP rating.

Maintenance considerations for plant teams

Magnetic switches allow users to access configuration without opening the detector. This supports non-intrusive operation and can reduce the need for routine adjustments to involve more than one person. Plug-in sensors can be replaced at the detector, and the display module can be removed to access the terminal area during installation or wiring work. These design features can simplify service tasks, although site procedures and applicable hazardous-area requirements still govern how work is performed.

The range includes poison-resistant flammable sensors and Surecell electrochemical sensors. Sensor choice should be based on the target gas and the application’s requirements; available options are not interchangeable across transmitter families. Teams should also confirm the selected calibration gas and calibration range for the sensor in use.

Applying the detector to a site specification

Sensepoint XCD is identified for applications including manufacturing, power generation, wastewater facilities, utilities, food and beverage production, refineries, chemical plants, and onshore and offshore oil and gas operations. Before specifying a detector, engineering and operations teams can work through a practical checklist:

  • Identify the gas hazard and choose a compatible sensor technology and range.
  • Confirm enclosure material, mounting method, entry type and applicable hazardous-area approvals.
  • Check the control-system interface requirements, including 4–20 mA sink/source wiring, relay functions and whether optional MODBUS is needed.
  • Plan cable sizing, voltage at the detector, environmental accessories and calibration access.
  • Document how maintenance inhibition, alarms and faults will be handled by site procedures and the control system.

Conclusion

A fixed gas detector is most effective when its sensor, outputs, installation and maintenance approach are matched to the site’s hazards and operating practices. Sensepoint XCD brings several gas-sensing options together with local status indication, configurable relays, selectable 4–20 mA wiring and optional MODBUS communication. For engineers and plant decision-makers, the key is to verify the exact sensor configuration, certification, wiring design and service requirements for each installation rather than treating the transmitter as a standalone choice.

Access Official Technical PDF

About The Author