Access Official Technical PDF

Share Summary:LinkedInEmail

An explosion-proof gas detector is one part of a broader safety and control strategy: it must be suited to the gas being monitored and able to communicate readings or alarms to the site’s monitoring system. The SD-1 Series is a smart gas detector/transmitter designed for combustible gases, selected toxic gases, oxygen and a range of organic vapors. Its sensor options, output configurations and hazardous-area approvals make it relevant to applications such as chemical and petrochemical plants, LNG terminals, power plants, utilities, and iron and steel works.

Explosion-proof gas detector for varied monitoring needs

The SD-1 Series is designed to detect hazardous atmospheres at either percent-of-lower-explosive-limit (% LEL) or parts-per-million (ppm) levels, depending on the model and target gas. This distinction matters when specifying a detector: combustible-gas monitoring commonly uses % LEL, while some toxic or organic compounds are measured in ppm. The SD-1GH semiconductor model, for example, covers a broad selection of gases, including acrylonitrile, ethylene oxide, methylene chloride and n-methyl pyrrolidone, as well as other compounds listed in the product information.

Other listed detection applications include methane, propane and hydrogen; carbon monoxide and hydrogen sulfide; carbon dioxide; and oxygen. The exact gas and measuring range depend on the selected model and sensor. The published ranges include 0–100% LEL for the catalytic SD-1GP, 0–10,000 ppm or 0–20% by volume for the infrared SD-1RI, model-specific ranges for the SD-1GH, 0–75 ppm for carbon monoxide and 0–30 ppm for hydrogen sulfide on the SD-1EC, and 0–25% by volume for oxygen on the SD-1OX.

Sensor choices and what they measure

The series uses several detection principles rather than one sensor technology for every gas. This allows the detector configuration to be matched to the measurement task. The available models are:

  • SD-1GP: Catalytic detection for a variety of hydrocarbons, with a 0–100% LEL measuring range.
  • SD-1RI: Infrared detection for carbon dioxide, with ranges specified as 0–10,000 ppm or 0–20% by volume.
  • SD-1GH: Semiconductor detection for a range of gases, with specific full-scale ranges shown in the product gas chart.
  • SD-1EC: Electrochemical detection for carbon monoxide and hydrogen sulfide.
  • SD-1OX: Galvanic-cell detection for oxygen.

Before specifying a model, confirm that the target gas appears in the applicable model’s detection information and check its listed range and alarm requirements. The gas chart includes distinct ranges for individual compounds; a range given for one gas should not be assumed to apply to another.

Outputs, alarms and control-system integration

The SD-1 provides a four-digit LED display for local readings and can communicate with other equipment through a 4–20 mA output or an optional HART configuration. The product information describes HART over 4–20 mA or a linear 4–20 mA output. Relay availability depends on the configuration: versions with 4–20 mA include one relay, while HART versions are specified without a relay.

The alarm function supports two programmable set points. Settings include increasing or decreasing operation, latching or self-resetting behavior, on and off delays, and energized or de-energized states. Relay contacts can be configured as normally open or normally closed. The listed contact capacity is 30 VDC at 0.5 A or 120 VAC at 0.5 A, subject to load resistance. These details should be checked against the receiving control system and the intended alarm sequence during design.

A microprocessor provides self-diagnosis for circuit and sensor failures, with a yellow fault lamp indicating a failure condition. This helps distinguish a reported fault from a gas reading at the detector, while alarm and monitoring responses remain dependent on the wider system configuration.

Hazardous-area design and maintenance access

The SD-1 is described as an explosion-proof design with ATEX and IECEx approvals and an Ex d IIC T5 classification; the listed approval details vary by model. SIL2 is available for the infrared, electrochemical and oxygen versions. These approvals are model-specific considerations, so project teams should confirm the applicable certification for the exact detector configuration and installation requirements.

The enclosure has an IP-65/67 ingress protection rating. The detector is intended for diffusion sampling, with a flow adapter and air aspiration available. For calibration and menu navigation, operators can use magnetic switches and a magnetic key, allowing access without opening the instrument in the hazardous atmosphere. The stated power supply is 24 VDC, with a 17–26.4 VDC range, and maximum power consumption is 3 W.

Practical specification considerations

For engineers and system integrators, selecting the SD-1 begins with the measurement objective, not simply the enclosure type. Confirm the target gas, desired units and full-scale range, then choose the corresponding detection principle and model. Next, establish how the reading and alarm states will be used by the control or monitoring system. In particular, verify the selected signal option, relay availability, alarm configuration and required approvals.

Operating limits also matter during installation planning. The stated temperature range is -20 to +60°C. Relative humidity is specified below 95% non-condensing, except for the SD-1EC, which is specified below 80% RH. Checking these conditions alongside power, sampling method and hazardous-area requirements helps determine whether the detector configuration fits the intended location.

Conclusion

The SD-1 Series brings multiple sensing principles and gas measurement options into an explosion-proof transmitter platform. Its practical value depends on matching the model to the target gas and range, then confirming that its output, alarm behavior and approvals align with the site’s instrumentation and safety requirements. A careful review of those configuration details supports a more informed specification for industrial gas monitoring.

Access Official Technical PDF

About The Author