Access Official Technical PDF

Share Summary:LinkedInEmail

Remote flammable gas detection is useful when the point that needs monitoring is hot, difficult to reach or unsuitable for routine interaction. The Sensepoint XCD RFD separates the sensing point from the transmitter: compatible flammable gas sensors can be installed remotely, while the transmitter remains in a location where personnel can read its display and use its controls. This arrangement is designed for applications such as gas turbine enclosures and solvent-based printing or coating ovens, including locations where high-temperature sensors are required.

How remote flammable gas detection is arranged

The Sensepoint XCD RFD transmitter can operate with compatible Sensepoint XCD remote catalytic bead or infrared sensors, as well as standard- and high-temperature Sensepoint flammable sensors. Depending on the sensor and installation arrangement, a sensor can be mounted directly at the transmitter’s bottom entry or remotely using a suitable junction box or duct mounting assembly. Remote sensors can be positioned up to 30 metres (100 feet) from the transmitter.

Separating the sensor from the interface can help address a practical installation constraint: the gas monitoring point may be in a restricted or elevated-temperature area, while inspection, configuration and maintenance need to take place somewhere more accessible. The transmitter’s remote location does not remove the need to select and install the sensor appropriately for the monitored environment.

Sensor choice and LEL range configuration

Sensor type should match the gas and operating conditions of the application. The system supports catalytic bead and infrared options for specified gases, as well as standard- and high-temperature flammable sensors. The high-temperature Sensepoint sensor is rated for operation up to 150°C (302°F), making it relevant where conventional ambient-temperature placement is not suitable.

The transmitter’s gas range can be adjusted from 0–100% LEL down to 0–20% LEL. A lower range can be appropriate with the high-temperature sensor, whose thermally matched beads are described as supporting accuracy and stability at low alarm levels. The source specifies that alarm set points can be as low as 5% LEL for this sensor configuration. Range selection and alarm settings should reflect the detection requirements of the installation and the compatible sensor’s specifications.

Clear local indication and configurable outputs

A large, tri-colour backlit LCD gives a visible indication of detector status. Steady green indicates normal operation, flashing yellow indicates a fault or warning, and flashing red indicates an alarm. This provides a quick visual reference for personnel, including where several detectors are present or a detector is not easy to approach.

Configuration is performed at the transmitter using non-intrusive magnetic switches and the display. Available settings include the measurement range, relay operation, alarm set points and the detector’s electronic tag number. During configuration, outputs are inhibited to reduce the risk of a false alarm at the control panel while maintenance or adjustment is under way.

For integration with a control system, the transmitter provides:

  • A selectable sink or source 4–20 mA current output.
  • Two programmable alarm relays and one programmable fault relay.
  • Local status indication and configuration at the transmitter.

The relays are programmable, with alarm and fault functions identified by default in the product documentation. Confirm the required relay logic and current-output configuration during system design and commissioning.

Installation considerations for integrators

The transmitter can be surface mounted using its integral mounting plate or installed on a horizontal or vertical pipe or structure with the optional mounting bracket. The documented pipe or structure cross-section is 40–80 mm. Accessories such as sunshade or deluge protection are also listed, where appropriate to the installation.

Because the equipment is intended for potentially explosive atmospheres, installation should follow applicable national guidance and use suitable mechanically protected cable and glands. The documentation specifies cable conductors from 0.5 mm² to 2.5 mm², with selection dependent on cable length and the voltage required at the detector. Cable-length figures are provided as guidance; the actual cable characteristics and installation conditions should be used to verify the design.

During wiring, the 4–20 mA output can be configured as either sink or source to suit the connected control system. The documentation also advises terminating the cable screen at the detector or controller, but not at both. Electrical design, earthing and installation details should be checked against the relevant equipment instructions and site requirements.

Operational and maintenance implications

Using a common transmitter platform with compatible sensors can simplify familiarisation and spares planning across installations using that platform. Non-intrusive adjustment allows routine configuration without opening the transmitter enclosure, while automatic output inhibition during adjustment helps avoid unnecessary control-panel alarms. The remote plug-in sensor option is also described as reducing maintenance time; the appropriate sensor and maintenance approach depend on the specific application.

For operations teams, the main value of the remote arrangement is practical: the sensing element can be placed near the potential gas hazard while status and controls remain accessible. That can make it easier to view detector condition and carry out configured maintenance without requiring the transmitter itself to be located in the same difficult area.

Choosing a suitable remote detection arrangement

Before specifying a Sensepoint XCD RFD installation, confirm the target gas, sensor type, temperature conditions, required measurement range, alarm strategy, transmitter location and distance between transmitter and sensor. Then verify mounting, cable sizing, control-system compatibility and hazardous-area installation requirements. Remote flammable gas detection is most effective as a correctly engineered system: sensor placement and selection, transmitter configuration and integration all need to suit the monitored process.

Access Official Technical PDF

About The Author