A 143 A soft starter can help control how a three-phase motor accelerates and stops, while providing adjustable current limiting and motor overload protection. The SIRIUS 3RW5055-6AB15 is rated for operating currents up to 143 A at 40 °C and supports a range of motor-control and communications functions. For engineers and plant teams evaluating the device, the key questions are how its ratings align with the motor and supply, which control functions are needed, and what installation and protection arrangements the system requires.
What the 3RW5055-6AB15 offers
This 3RW50 soft starter is designed for operating voltages from 200 to 600 V and three-phase motor applications. Its listed motor power ratings at 40 °C are 37 kW at 230 V, 75 kW at 400 V and 90 kW at 500 V. The product designation also identifies a 400–600 V, 143 A device; actual selection should account for the motor, supply conditions, ambient temperature and applicable installation requirements.
Current capacity changes with ambient temperature: the rated operating current is 143 A at 40 °C, 128 A at 50 °C and 118 A at 60 °C. The manufacturer specifies operation from -25 °C to +60 °C and notes that derating applies at 40 °C and above. These ratings make thermal conditions an important part of sizing, particularly where equipment is installed in a warm enclosure or other elevated-temperature location.
Starting, stopping and current control
The soft starter provides ramp-up and ramp-down functions, as well as Soft Torque and pump ramp-down capability. Start-up ramp time and stopping time are each adjustable from 0 to 20 seconds. Starting voltage can be set from 30% to 100%, while adjustable current limitation ranges from 130% to 700%. These controls give commissioning teams parameters to configure motor acceleration and deceleration for the application rather than relying solely on direct-on-line starting.
The unit controls two phases and includes an integrated bypass contact system. It also provides electronic motor overload protection, intrinsic device protection, auto-reset and manual reset functions. The listed trip classes are CLASS 10A, 10E (preset) and 20E, in accordance with IEC 60947-4-2. The specified recovery time is 300 seconds. The device does not provide motor thermistor connection inputs, so applications that require thermistor-based motor protection need to account for that separately.
Communications, outputs and configuration
Communication capability is available through compatible modules. Supported options include PROFINET, PROFIBUS, Modbus TCP, Modbus RTU and EtherNet/IP. PROFIenergy is supported in connection with the PROFINET Standard communication module. HMI Standard and HMI High Feature modules are also supported, providing accessory-dependent options for operation and visibility.
The device has one digital input, three digital outputs and one analog output. Two digital outputs are not parameterizable; the output configuration is two normally open contacts and one changeover contact. The analog output is 4–20 mA by default. With the High Feature HMI, it can be parameterized for 0–10 V. Operating measured-value display and the error logbook are available only with special accessories. Software configuration is supported, but software parameterization is not listed as available.
Electrical protection and installation planning
Protection and coordination should be selected for the specific installation. The product data lists compatible circuit breakers, gG fuses, semiconductor-protection fuses and line contactors, with different coordination types and short-circuit ratings. UL fuse recommendations are also provided for standard- and high-fault applications. These references are selection inputs, not a substitute for checking the applicable coordination, fault level and local requirements for the complete motor branch circuit.
The control supply is 110–250 V AC at 50 or 60 Hz. The main current circuit uses busbar connections, while the control circuit uses screw terminals. The unit measures 198 mm high, 120 mm wide and 249 mm deep, with a weight of 3.2 kg. Installation drawings and the specified clearances should be reviewed during panel layout: the listed spacing includes 100 mm above and 75 mm below, as well as 5 mm at the side.
Maximum installation altitude is 5,000 m, with derating required above 1,000 m. The enclosure protection rating is IP00; IP20 protection against vertical front touching is specified when additional terminal covers are fitted. The maximum cable length between soft starter and motor is 800 m. Confirm conductor sizing, terminal arrangements, tightening torques and environmental conditions against the product documentation before installation.
Applying the soft starter in a motor-control system
When assessing the 3RW5055-6AB15, start by matching the motor’s current and power requirements to the device ratings at the actual ambient temperature. Then determine the required start and stop behavior, current limit, overload trip class and reset approach. Finally, specify communication modules, HMI accessories and protective devices according to the control architecture and electrical design.
The practical value of this 143 A soft starter lies in combining adjustable motor starting and stopping with overload protection, an integrated bypass system and optional industrial communications. Correct application depends on checking derating, protection coordination, wiring and accessory requirements—not just the headline current rating. Bringing those factors into the design and commissioning review helps ensure the starter is suited to both the motor and the wider automation system.