The Sony IMX458-AALH5 is a 13-megapixel CMOS image sensor designed around a stacked, back-illuminated architecture. Its combination of high-resolution capture, high-speed readout options, raw HDR output and MIPI CSI-2 connectivity may interest engineers evaluating imaging components for embedded vision and automation-related systems. However, the device’s stated design purpose is cellular phones and tablets, so its specifications should be considered alongside the intended application and the manufacturer’s product-use qualifications.
How the IMX458 CMOS image sensor is designed
The IMX458-AALH5 is a stacked CMOS active-pixel sensor with a square pixel array. Its imaging area uses backside illumination, while the stacked design incorporates column-parallel analog-to-digital converter circuits. Sony describes these technologies as supporting high-speed image capture and high sensitivity with low noise compared with conventional CMOS image sensors.
The sensor uses an RGB primary-color pigment mosaic filter to capture color information. Its unit cell measures 1.12 µm by 1.12 µm, and the device has a diagonal size of 5.867 mm, designated Type 1/3.06. These physical and pixel dimensions are relevant when assessing optical compatibility, image detail and the constraints of a camera module.
Resolution figures vary according to which pixel area is being described. The sensor has approximately 13.48 million total pixels at 4224 × 3192, approximately 13.28 million effective pixels at 4224 × 3144, and approximately 13.13 million active pixels at 4208 × 3120. The active-pixel figure is the one used in the listed full-resolution drive mode.
HDR and image capture modes
The sensor supports high dynamic range still images and movies using spatially multiplexed exposure technology, and it can output raw data in HDR mode. In practical system design, HDR can help capture scenes that include different brightness levels within the same image. The usefulness of that capability depends on the camera configuration and downstream processing; the sensor specification does not prescribe a complete image-processing workflow.
An electronic shutter provides variable integration time, giving the system a way to set how long the sensor collects light for an exposure. The product information lists a minimum sensitivity of 153 LSB at F2.8 with a 1/120-second integration time, and a minimum saturation signal of 1023 LSB. These are specified sensor characteristics, not a guarantee of image quality in every optical, lighting or operating condition.
Available readout modes trade image dimensions for frame rate:
- Full resolution: 4208 × 3120 active pixels, approximately 13.13 megapixels. The basic drive-mode table lists 30 frames per second in normal mode and 40 frames per second in HDR mode.
- Vertical 1/2 subsampling: 2100 × 1560 pixels, approximately 3.28 megapixels, at up to 60 frames per second.
- Vertical 1/3 binning: 1400 × 752 pixels, approximately 1.05 megapixels, at up to 123 frames per second.
The feature list also identifies 4K2K capture at 30 frames per second in normal and HDR modes, and 1080p capture at 90 frames per second in normal mode. The listed output formats are RAW10 and RAW8. When comparing modes, engineers should distinguish the feature summary from the specific dimensions and rates in the basic drive-mode table, then confirm the required configuration against the detailed device documentation.
Interfaces and system integration considerations
Image data is sent over a CSI-2 serial interface supporting two- or four-lane MIPI operation, with a maximum stated rate of 1.3 Gbps per lane and compliance with the D-PHY specification version 1.1. The sensor also provides two-wire serial communication. These interfaces shape how the component connects to a host processor and how control and image data are handled within a camera system.
Two PLLs support independent clock generation for pixel control and the data-output interface. Other listed functions include pixel binning, vertical subsampling, independent flipping and mirroring, dynamic defect-pixel correction, fast mode transition, and dual-sensor synchronization. A built-in temperature sensor and 4-kbit user OTP ROM are also included. Their presence identifies available device functions, but system designers still need to determine how each feature fits their control, calibration and data-handling requirements.
The sensor operates with three supply voltages: 2.7 V analog, 1.2 V digital, and 1.8 V for the input/output interface. Power-tree design must account for these separate rails and the requirements of the surrounding electronics. The product information describes low power consumption as a design feature but does not provide a numerical consumption figure in the supplied specifications.
Check application suitability before selection
One qualification is especially important for industrial projects: Sony states that the IMX458-AALH5 is designed for cellular phones and tablet PCs. The manufacturer does not guarantee product quality and reliability when it is used in another application. It also states that individual specification changes cannot be supported because the device is a standard product.
For an automation camera or embedded-vision design, component selection should therefore consider more than resolution and frame rate. Confirm that the intended use is compatible with the manufacturer’s stated application scope, and review the complete device documentation for operating, interface and configuration details before committing to a design. The sensor’s listed capabilities do not, by themselves, establish suitability for a particular industrial environment or system.
Conclusion
The IMX458-AALH5 offers a compact 13-megapixel imaging platform with stacked, back-illuminated pixels, HDR raw output, multiple readout modes and MIPI CSI-2 connectivity. Those features provide several parameters for camera-system evaluation, from image dimensions and frame rate to power rails and host-interface requirements. For industrial automation decision-makers, the key practical step is to weigh those technical options against the application requirements—and to treat the manufacturer’s cellular and tablet design intent as a material qualification when considering other uses.