Access Official Technical PDF

Share Summary:LinkedInEmail

In a camera system, the CMOS image sensor power supply is more than a way to deliver the required operating voltages. Its noise and startup behavior can influence image quality, particularly when ripple reaches the sensor’s analog circuitry. The AR0143 reference design demonstrates an approach to powering a sensor with separate analog, digital I/O and digital-core rails, while paying particular attention to the analog supply.

These design considerations matter wherever camera modules must combine compact integration with dependable imaging. The reference design was developed for an automotive application, but its underlying lesson is broadly relevant to engineers integrating image sensors: power integrity and sequencing should be considered alongside the sensor, clock and PCB layout.

Why sensor power integrity affects image quality

CMOS image sensors integrate functions such as timing logic, image digitization, processing and capture control on a single chip. This integration can reduce system size, power and cost compared with architectures that rely on more separate components. It also places sensitive imaging circuitry in a compact system where electrical noise needs to be managed.

Potential noise sources include electromagnetic interference, substrate coupling, thermal noise and power-supply ripple. The reference design note focuses on supply ripple. Its impact depends in part on which sensor rail is affected: ripple on a digital supply is generally less likely to affect image quality when it remains within the specified limits, while ripple on an analog rail can contribute to visible image artifacts.

Possible effects include image noise and banding. For this reason, a design that meets nominal voltage requirements still needs to account for voltage stability and behavior during operating transitions.

AR0143 power architecture: three sensor rails

The AR0143 uses three supply voltages for its sensor circuitry:

  • 2.8 V analog supply: VAA and VAAPIX, identified in the design note as the rail most important to picture quality.
  • 1.8 V digital I/O supply: VDDIO, which powers the sensor’s digital interface circuitry.
  • 1.2 V digital-core supply: VDD, used for the digital core and image processing.

The camera module reference design also shows a 3.0 V VMID rail and an input module voltage, VMOD, in the 3.9–4.6 V range. Three DC-DC converters provide the 3.0 V, 1.8 V and 1.2 V rails, while an NCV8163 linear regulator provides the 2.8 V analog rail from VMID. This division assigns a low-dropout regulator to the supply that the design identifies as especially sensitive to ripple.

Why the analog rail gets special attention

A regulator choice for an image sensor should be evaluated against the needs of the specific rail, rather than treated as a uniform power-tree decision. In this design, the analog supply is supplied by the NCV8163. The design note highlights the regulator’s transient response, power-supply rejection ratio (PSRR) over a wide frequency range and low dropout voltage as relevant characteristics for this role.

PSRR describes how effectively a regulator limits the transfer of input-voltage variation to its output. For a sensitive analog rail, reducing ripple at the sensor supply can help avoid a source of image disturbance. The reference design reports low ripple on VAA during normal operation and includes a transient waveform for the 2.8 V rail when supplied from the 3.0 V VMID rail.

The note also points to low dropout as a way to limit regulator voltage headroom and reduce power dissipation. It describes the NCV8163 output as cleaner than a DC-DC converter output, with lower output capacitance than a DC-DC converter, as part of the proposed design’s cost-efficiency rationale. These are design-note claims for the presented implementation, not a substitute for checking component behavior in a specific application.

Plan sequencing as well as steady-state voltage

Power integrity is not only a steady-state concern. Sensor rails and clock signals must behave appropriately during startup and shutdown. The AR0143 reference material includes timing waveforms for the supply rails and shows the time relationship between the VDDIO rail and the sensor clock during both startup and shutdown.

For engineers reviewing a camera power tree, this makes sequencing a concrete verification task. Check that the relevant rails reach their required conditions in the intended order and that the clock timing is compatible with the sensor’s power transitions. The design note provides timing examples, but implementation details should be validated against the sensor requirements and the behavior of the chosen components.

Practical design and validation considerations

The reference design offers several useful review points for sensor integration:

  • Identify the sensitive rail. Distinguish analog power from digital I/O and core supplies, and assess ripple according to each rail’s role.
  • Match regulation to the rail. Consider whether a switching converter or linear regulator is appropriate for each supply, including ripple, transient response and dropout requirements.
  • Review startup and shutdown. Examine rail timing alongside clock behavior, not just the voltage levels during normal operation.
  • Measure the implemented design. Use the sensor and regulator specifications as requirements, then validate operating parameters and waveforms in the actual application.

The design note identifies the AR0143 implementation as automotive AEC-Q100 qualified and presents a compact camera-module reference design. Qualification and performance still need to be considered in the context of the parts and complete system selected for a particular product.

Conclusion: treat image-sensor power as part of the imaging design

The AR0143 example shows why a camera’s power tree deserves the same careful attention as its sensor and signal paths. Separate analog, I/O and core rails provide a structured basis for power delivery, while a low-ripple analog supply and deliberate startup and shutdown timing address factors that can affect image quality. For system integrators and design engineers, the practical takeaway is to verify rail quality and sequencing in the finished application rather than relying on nominal voltage values alone.

Access Official Technical PDF

About The Author