An organic-film image sensor developed by NHK uses vertically layered sensing materials to capture red, green and blue information within each pixel. The research addresses a familiar design trade-off in single-chip color cameras: conventional color-filter mosaics derive a full-color image from information gathered across multiple pixels, rather than recording every color component at every pixel location. The layered approach is intended to support high-resolution imaging and more efficient use of incident light, with further development focused on reducing pixel size and increasing pixel count.
Why pixel-level color capture matters
In a typical single-chip color camera, red, green and blue filters are arranged in a mosaic over an image sensor. Each pixel therefore receives one portion of the color information. The camera combines measurements from neighboring pixels to reproduce a color image. As a result, the resolution of the reconstructed image and the utilization of light are lower than the capabilities of the individual pixel devices, according to the research description.
The three-layer design takes a different route. Rather than assigning different color filters to neighboring pixels, it separates color detection by wavelength through vertically arranged sensing layers. Red, green and blue measurements can therefore be obtained at the same pixel position. This is the central architectural distinction: color information is collected through depth within the sensor, rather than distributed across a surface mosaic.
How the three-layer organic-film image sensor works
The sensor combines two organic films with a CMOS image sensor. The upper organic film responds to blue light, the next organic film responds to green light, and the CMOS layer detects red light. Each layer is designed to absorb its target color while allowing the other relevant color components to pass through.
- Blue detection: Incident light reaches the blue-sensitive organic film first. The film absorbs the blue component and converts it into an electrical signal, while transmitting green and red light.
- Green detection: The transmitted light reaches the green-sensitive organic film. This layer absorbs the green component and allows red light to continue onward.
- Red detection: The remaining red component reaches the CMOS image sensor, which detects it.
Transparent thin-film transistors are combined with the organic layers. Signals produced by the individual sensing layers can be combined to reproduce a color image. The blue organic film was developed in collaboration with Nippon Kayaku Co., Ltd.
Reported specifications and development status
The reported device had a pixel array of 320 horizontal by 240 vertical pixels, a pixel pitch of 20 micrometers, and a frame rate of 60 frames per second. Its structure placed the blue organic film over a glass substrate and the green organic film over the red-sensitive CMOS image sensor. The blue film was positioned facing the green film.
These specifications describe the device reported in the research; they should not be read as a specification for a production camera or as evidence of readiness for a particular industrial vision task. The stated development direction was to reduce pixel size and increase the number of pixels, while continuing research toward a compact, high-resolution, single-chip camera.
Potential relevance to industrial imaging
For automation engineers and machine-vision system integrators, the architectural idea is relevant because cameras are often selected according to the detail and color information a process needs to capture. A sensor that obtains all three color components at each pixel could, in principle, address limitations associated with reconstructing color from measurements distributed across neighboring pixels. The reported work identifies higher image resolution and improved light utilization as intended advantages of this structure.
However, the available information does not establish how the device performs in specific inspection conditions or compare it with commercial industrial cameras. It also does not provide details on factors such as sensitivity, dynamic range, noise, operating temperature, interface options, or long-term reliability. Those characteristics would need to be evaluated before determining suitability for tasks such as automated inspection, measurement, or process monitoring.
For technical decision-makers, the practical takeaway is to distinguish a promising sensor architecture from a deployable camera specification. The layered design offers a different way to acquire color information, while its reported pixel count and ongoing development indicate that further work was planned before compact, high-resolution camera implementation.
Conclusion
The three-layer organic-film image sensor captures blue and green light with organic films and red light with a CMOS layer, producing color information within each pixel. This approach is designed to avoid the color-mosaic method’s reliance on data from multiple pixels and to use incident light more efficiently. Its potential significance for industrial imaging will depend on continued progress in pixel size and resolution, as well as performance data relevant to real operating environments. For now, it represents a sensor concept worth tracking rather than a validated solution for a specific automation application.