Access Official Technical PDF

Share Summary:LinkedInEmail

Automotive power electronics thermal management is becoming more challenging as electric-drive systems are designed for greater power density, higher operating temperatures, and longer service life. Battery-electric vehicles and high-power charging increase the demands placed on inverters, power modules, and electric machines. Meeting those demands requires more than adding a larger heat sink: engineers must consider cooling, packaging materials, interfaces, and reliability as parts of one system.

Research presented by the National Renewable Energy Laboratory (NREL) illustrates this connected approach. Its work examines compact power-electronics packaging, cooling methods, material behavior, and thermal-mechanical failure mechanisms relevant to electric-drive applications.

Why automotive power electronics thermal management matters

Vehicle designs are moving toward compact, power-dense systems, including planar power-electronics construction. The whitepaper describes a goal of reducing power-electronics volume by a factor of 10, alongside lower cost and improved reliability. Such targets leave less room for heat to spread and make thermal design more consequential.

Wide-bandgap (WBG) devices can support power-electronics designs with higher power density, voltage, and switching frequency. But compact WBG-based systems also require components and materials rated for higher temperatures, effective heat-transfer technologies, and thermal management at the system level. Heat must travel from the semiconductor through die attach, substrate, interfaces, base plate, and cooling structure. Resistance at any part of this path can affect device temperatures.

Reliability targets add another constraint. The source identifies increased fleet use and long-range battery-electric vehicles as drivers of longer service-life expectations and high-rate power transfer. Designs therefore need to address both operating temperature and the way repeated thermal and mechanical stresses change materials over time.

Cooling compact power modules

One NREL concept investigated dielectric-fluid cooling in a planar package. A dielectric fluid can contact electrical components without conducting electricity, allowing the cooling arrangement to be integrated closely with the power devices and interconnects. The proposed design used single-phase heat transfer, with jet impingement and finned surfaces to improve cooling. It also aimed to cool bus bars and electrical interconnects, with the goal of reducing temperatures in nearby capacitors and gate drivers.

The modeling work set a specific design challenge: a 100 kW inverter, a maximum device temperature of 250°C, and a module-plus-cold-plate volume below 240 mL. For a modeled manifold distributing fluid to 12 devices, the reported cold-plate and power-module volume was 120 mL. The modeled flow rate was 4.1 L/min at a pressure drop of 0.33 psi. These are results for the design and conditions described, not universal design values.

Experimental validation used cartridge heaters to simulate devices and heat fluxes above 700 W/cm2. A prototype cold-plate manifold was 3D printed in lightweight plastic for testing; the work also noted that conventional manufacturing methods could be used to fabricate the cold plate. This progression—from thermal target to model to prototype—helps engineers assess whether a compact cooling concept is practical before integrating it into a complete system.

Packaging materials and power module reliability

Thermal performance depends on package materials as well as coolant flow. Substrates, attachment layers, and bonded interfaces must transfer heat while tolerating differences in thermal expansion. When adjoining materials expand by different amounts during temperature changes, stresses can develop and contribute to cracking or separation.

NREL’s reliability work examined bonded materials, including pressure-assisted sintered silver. Samples joining copper and Invar were thermally cycled between -40°C and 200°C, with bond condition checked periodically using C-mode scanning acoustic microscopy. The reported observations included faster crack growth on the Invar side and a combination of cohesive and adhesive failure mechanisms. The results point to the importance of both larger-scale material mismatch and local interface behavior when evaluating a package.

Organic direct-bond-copper (ODBC) substrates were also assessed. In the reported package tests, ODBC thermal performance was similar to aluminum nitride. ODBC samples underwent thermal shock, thermal aging, and power cycling; the whitepaper reported no significant decrease in electrical or thermal performance during the testing described. Such findings are specific to the tested samples and conditions, but they illustrate why thermal characterization and reliability testing should accompany material selection.

Electric machine cooling and interface characterization

Electric motors face related challenges as designers seek higher current density and power density. The thermal path can run from winding conductors through slot liners, stator laminations, and the motor housing. Heat transfer depends not only on the bulk conductivity of these materials but also on contact resistance at their interfaces.

Research activities described in the whitepaper included direct fluid-jet impingement on motor windings and evaluation of automatic transmission fluid as a cooling medium. Experiments examined heat-transfer behavior under different conditions. In the reported ATF tests, the heat-transfer coefficient increased as the cooled surface temperature increased; other parameters, including nozzle distance and incidence angle, were also identified for evaluation.

Characterizing thermal contact resistance between motor laminations and at winding-to-liner or liner-to-stator interfaces can improve the accuracy of thermal models. Models validated against experimental data help engineers estimate temperatures more realistically and compare design options, rather than relying on material conductivity values alone.

Design implications for engineers

For system integrators and design teams, the practical lesson is to treat thermal management and reliability as coupled design tasks. A useful workflow includes:

  • Define thermal and packaging targets: Set limits for device temperature, heat load, cooling-system volume, and other system constraints.
  • Model the complete heat path: Include package layers, interfaces, cooling plates, fluid distribution, and relevant electric-machine components.
  • Characterize materials and interfaces: Measure thermal behavior and assess how temperature cycling may affect bonded or contacting materials.
  • Validate predictions: Use representative prototypes and test conditions to check thermal models and cooling concepts.
  • Assess lifetime mechanisms: Use cycling data and failure analysis to inform predictive and remaining-life models.

Compact cooling can support higher power density, but it does not remove the need to verify flow distribution, pumping requirements, temperature limits, and package durability together. Likewise, a promising substrate or bonding material needs evaluation under relevant thermal and electrical stresses.

Conclusion

As electric-drive systems become more compact and demanding, automotive power electronics thermal management must account for the entire system: semiconductor devices, package materials, thermal interfaces, cooling hardware, and electric-machine heat paths. Modeling, experimental validation, and failure-mechanism analysis provide complementary tools for balancing power density with reliability. For engineers and plant-level decision-makers evaluating electrification technologies, integrating these activities early can support more informed choices about cooling architecture, materials, and service-life expectations.

Access Official Technical PDF

About The Author