Bidirectional DC-DC converters are a key interface in hybrid energy storage systems (HESS), where power must move both to and from storage devices. For automation engineers and system designers working with renewable generation, microgrids, or DC power systems, converter topology and control determine how storage units support the DC bus and respond to changing power demand.
A common HESS combines a lithium-ion battery with a supercapacitor. The battery offers relatively high energy density, while the supercapacitor provides high power density, fast response, and a longer cycle life. These different characteristics can complement one another, but only if the power electronics and energy-management strategy allocate power appropriately.
Why combine batteries and supercapacitors?
Renewable sources such as wind and solar can vary over time, creating a need to balance generation and consumption. Storage can help address that imbalance. In a hybrid system, the battery is suited to longer-term energy needs, while the supercapacitor can respond to faster power changes. The aim is to use each device according to its characteristics rather than requiring one storage technology to handle every operating condition.
Power converters connect the storage units to the DC bus and regulate charging and discharging. During charging, energy flows from the grid or a renewable source toward storage. During discharge, energy flows from storage to the bus to support a load or meet a power shortfall. Control must manage the direction and amount of this transfer and coordinate transitions between operating modes.
Bidirectional DC-DC converter topologies
Non-isolated buck-boost converters
A bidirectional buck-boost converter can step voltage up or down while transferring power in either direction. In charging mode, it operates as a buck converter, reducing the DC-bus voltage as needed to charge the battery. In discharge mode, it operates as a boost converter, raising the battery-side voltage to supply the bus. The control system determines the operating mode and regulates power transfer.
A related arrangement connects a battery and supercapacitor to a common DC bus through bidirectional conversion stages. This allows the storage devices to operate at their own voltage levels, making their stored energy available to the system. The controller must select or coordinate the storage unit according to the disturbance or power imbalance being addressed.
Isolated full-bridge converters
Where galvanic isolation is required, a bidirectional full-bridge converter uses bridges on both the low- and high-voltage sides, with a transformer between them. The transformer provides electrical isolation and contributes to the conversion ratio. The battery is typically connected to the low-voltage side.
Power flow changes the roles of the two bridges. During charging, the high-voltage-side bridge acts as an inverter and the low-voltage-side bridge as a rectifier. During discharge, their operation reverses. This topology therefore supports two-way transfer while maintaining isolation between the voltage sides.
Interleaved and multi-port designs
Interleaved converters divide current among multiple phases. In a three-phase arrangement, phase currents are offset so their combined current ripple can be reduced. Sharing current also reduces current stress on individual phases and can allow smaller inductors and capacitors. The reviewed topology discussion also identifies soft-switching techniques as a means of reducing switching losses and improving converter efficiency.
Multi-port DC-DC converters provide another way to connect multiple sources and storage devices. Configurations include single-input, multi-output; multi-input, single-output; and multi-input, multi-output designs. A multi-input, multi-output arrangement can combine sources with different voltage and current characteristics and provide different output voltage levels. The stated design goals include reducing the number and cost of power-electronic components while supporting system reliability and efficiency.
Control and energy management for hybrid storage
Current-mode control
Current-mode control commonly uses two feedback loops: an inner loop regulates current, and an outer loop regulates DC-bus voltage. The inductor current corresponds to battery charging or discharging current, so regulating it provides direct control of storage current. This approach can respond quickly and provide short-circuit protection, but it can also be vulnerable to instability and sub-harmonic oscillations.
Power control and operating modes
Control priorities can differ between grid-connected and islanded operation. In grid-connected mode, battery control can be based on state of charge (SOC). In islanded mode, maintaining microgrid stability and power quality becomes a priority. The reviewed approaches include fuzzy control and advanced droop control based on the degree of voltage disturbance.
Allocating power between storage devices
In a passive HESS, the sources share power according to their internal impedances. A supercapacitor connected in parallel with a battery can carry fast power deviations, helping reduce frequent partial discharges of the battery. In an active arrangement, a controller can divide power using a linear filtering method: lower-frequency power demand is assigned to the battery, while the remaining, faster-changing component is handled by the supercapacitor.
Filtering is a starting point, not a complete energy-management strategy for every operating condition. The control design may also need to account for storage losses, response times, SOC, power and energy limits, and—in some systems—predictions of renewable generation. Rule-based, fuzzy, or neural-network-based methods are identified as possible ways to address multiple factors.
Practical implications for system design
Topology selection and control strategy should be considered together. A non-isolated buck-boost converter offers bidirectional voltage conversion; a full-bridge topology provides galvanic isolation; interleaving distributes current across phases; and multi-port designs can connect several DC sources. Each choice shapes how the HESS interfaces with the bus and how the controller can allocate power.
For engineers and technical decision-makers, the central task is to match converter operation and energy management to the storage devices’ roles and the system’s operating modes. Coordinated control can help direct fast power changes to the supercapacitor and longer-term demand to the battery, while maintaining bus regulation and supporting stable power delivery. The appropriate design depends on the required power flow, isolation needs, source characteristics, and control objectives.