For operators considering large-scale energy storage, a redox flow battery (RFB) offers an important design advantage: power and energy capacity can be scaled separately. The electrochemical cell determines power, while the quantity of electrolyte held in external tanks determines energy capacity. In aqueous systems, however, the amount of dissolved active material—and therefore the energy stored per unit volume—is limited by solubility. Adding solid redox-active materials, known as solid boosters, is a proposed way to store additional charge in the electrolyte reservoirs without relying only on dissolved species.
The approach was investigated in acidic and neutral-pH aqueous systems. Its central idea is to transfer charge between dissolved redox-active molecules and a solid material in the liquid phase. The results show how material selection and electrical conductivity can influence whether this strategy increases battery capacity.
Why aqueous redox flow battery capacity is constrained
In a conventional RFB, positive- and negative-side electrolytes circulate from separate tanks through an electrochemical cell. Oxidation and reduction reactions at porous electrodes convert electrical energy to chemical energy during charging, with the reactions reversing during discharge. Because the active species are dissolved in the liquids, the concentration that can be achieved is a key factor in the charge stored in a given electrolyte volume.
For aqueous RFBs, the solubility limit of those species constrains volumetric energy density. The thesis describes typical aqueous systems as having a volumetric energy density of approximately 25–40 Wh/L, while its abstract cites a broader range of 10–40 Wh/L for RFBs. This limitation matters when a design needs more stored energy but increasing tank volume is undesirable.
Solid boosters address the capacity challenge by introducing another storage medium into the liquid electrolyte. Rather than replacing the dissolved redox species, the solid material can accept charge from them. In principle, this lets the reservoir hold charge in both the solution and the dispersed solid phase.
How redox-mediated charge transfer works
The charge-transfer mechanism depends on the electrochemical relationship between the dissolved redox couple and the solid booster. When their energy levels—described in the work in terms of Fermi-level alignment—are suitably matched, the dissolved species can transfer charge to or from the solid. The solution species acts as a redox mediator: it participates in the reaction at the flow-cell electrode and then transfers charge to the booster in the reservoir.
This differs from relying on direct contact between every solid particle and the cell electrode. The liquid redox species provides a pathway for charge exchange between the electrochemical cell and solid storage material. For an engineering design, that means compatibility is essential: the redox potential of the mediator and the accessible redox transitions of the solid must support the intended charging and discharging reactions.
Electrical conductivity is another important consideration. The research paired several boosters with carbon-based materials, including carbon black and carbon nanotubes, to improve electronic conductivity during cycling. The work therefore treats the booster not simply as a high-capacity material, but as part of a composite whose electrochemical behavior must be suitable in the chosen electrolyte.
Two aqueous battery approaches demonstrate the concept
Polyaniline in an acidic system
In an acidic aqueous flow battery, polyaniline (PANI) was evaluated as a solid booster with iron and vanadium redox-active species. A composite of polyaniline and carbon acetylene black was placed in both electrolyte reservoirs. The reported volumetric capacity was three times that of the electrolytes alone.
This result illustrates the role of both the active polymer and the conductive additive. Polyaniline supplies redox-active solid storage, while carbon black is incorporated to support electronic conductivity. It also shows that the booster configuration can be assessed alongside the chemistry already circulating through the cell, rather than as a standalone electrode material.
Copper hexacyanoferrate in a neutral-pH system
A separate investigation focused on the positive side of a neutral-pH aqueous battery. It paired copper hexacyanoferrate (CuHCF), a Prussian blue analogue, with carbon nanotubes and an organic redox mediator. The thesis abstract reports a 104-fold increase in volumetric capacity compared with the initial electrolyte. This result is specific to the reported system and should not be read as a general performance expectation for other chemistries or operating conditions.
The work also explored a candidate negative-side chemistry: a newly synthesized viologen-derived redox molecule paired with a polyimide booster. Its viability was tested preliminarily, and scanning electrochemical microscopy was used in an initial investigation of charge-transfer kinetics at the solid–liquid interface. These measurements represent early investigation of the mechanism, not a demonstration of a fully developed battery design.
What engineers should consider when evaluating boosters
For system integrators and battery developers, the approach highlights several linked design questions:
- Redox compatibility: Can the dissolved mediator exchange charge with the solid booster over the intended operating range?
- Conductivity: Does the booster, alone or in a carbon composite, support the electron-transfer processes needed during cycling?
- Electrolyte conditions: Is the material suitable for the system’s pH and supporting electrolyte?
- Interface kinetics: How readily does charge transfer occur between the dissolved species and solid surface?
- System-level validation: Do capacity gains remain useful when the complete cell and its cycling behavior are considered?
These questions connect materials selection to the practical requirements of a flow-battery system. A capacity increase in a laboratory configuration does not, by itself, establish performance across different chemistries or operating conditions. Further work is needed to characterize charge transfer, cycling, and integration in larger-scale demonstrations.
Conclusion: expanding storage beyond dissolved species
Solid boosters offer a route to increase the amount of charge stored in aqueous redox flow battery reservoirs by adding a redox-active solid phase to the liquid electrolyte. Results with polyaniline/carbon black in an acidic system and CuHCF/carbon nanotubes in a neutral-pH system demonstrate the potential of redox-mediated charge transfer. For industrial energy storage, the practical opportunity lies in combining suitable mediator and booster chemistry with adequate conductivity and verified interfacial kinetics. The approach is promising, but further development is needed to establish its performance and suitability in industrial demonstrators.