The CAS 2018 conference brought together researchers working across semiconductor devices, integrated circuits, microsensors, microsystems and related technologies. Its preliminary program, issued on August 9, 2018, outlined three days of plenary talks, technical presentations, a focused workshop and poster sessions. For industrial automation engineers and technical decision-makers, the program offers a useful snapshot of research areas that underpin sensing, power electronics, communications and embedded systems.
Organized by the National Institute for R&D in Microtechnologies IMT Bucharest, the event ran from October 9 to 12. Although the program was centered on research rather than factory deployments, many of its topics connect to components and methods used in automation equipment: sensors, signal-conditioning circuits, reliable power devices, wireless systems and microsystems integration.
CAS 2018 conference themes: devices, circuits and integration
The opening plenary session covered several directions in electronics research. Topics included low-dimensional structures for future electronics, heterogeneous integration for radio-frequency and millimeter-wave systems, and processing challenges in silicon carbide (SiC) and gallium nitride (GaN) power devices. These subjects span material and device development through to packaging and system integration.
Power semiconductor technology is particularly relevant to industrial electronics, where devices must support power conversion and control functions. The program included work on SiC MOSFET interface traps and SiC superjunction IGBTs, alongside sessions on power-management circuits. Other integrated-circuit presentations addressed charge pumps, low-power circuit design, current mirrors, output buffers and voltage regulators.
The program also included papers on fault detection and reliability. Presentations examined fault assessment in automotive smart-power products, fault reporting in galvanically isolated IGBT gate drivers, and the reliability of FPGA input/output blocks under ionizing radiation. These are application-specific research topics, but they reflect a wider engineering concern: evaluating how electronic components behave when exposed to demanding operating conditions or faults.
Microsensors and microsystems for measurement
Measurement technologies featured throughout the program. A plenary presentation considered analytical modeling of thermopile-based MEMS sensors for simultaneous detection of pressure and gas composition. Other sessions included a resistor-based temperature sensor, sensing methods based on cavity perturbation, and a probe for millimeter-wave characterization of skin tissue.
For automation teams, sensor research is relevant because measurement is the starting point for monitoring and control. The conference program did not present these studies as ready-made industrial products. Instead, it showed how device structures, sensing principles and supporting electronics are investigated as building blocks for future systems.
The program also highlighted microsystems assembly and integration. One presentation addressed low-temperature packaging methods as enablers for microsystem assembly. Packaging is part of the engineering chain between a sensor or microdevice and its use in a larger electronic system, making it a practical consideration for designers assessing integration constraints.
Energy harvesting and environmental monitoring
A two-part workshop focused on microsystems for energy harvesting and environmental monitoring. Its sessions connected piezoelectric MEMS, sensor materials, energy conversion and water-quality measurement. Presentations covered piezoelectric MEMS for energy harvesting, a power-harvesting and storage circuit for piezoelectric cantilevers, and the design and simulation of a piezoelectric energy harvester for aerospace applications.
The environmental-monitoring portion included electrochemical sensors for ionic species in natural water sources, a system for nitrite and nitrate detection, and coatings for electronic water-pollution sensors. A separate presentation described a photovoltaic panel for portable applications. Together, these topics illustrate the range of components and supporting circuits involved when designing a measurement system that may need to operate away from conventional power sources.
The workshop also showed how such work spans disciplines: device fabrication, materials, sensor chemistry, electronics and system-level design. For system integrators and operations leaders, that breadth is a reminder that a monitoring solution is not defined by the sensor alone. Its power, packaging and measurement electronics also matter.
Modeling, microwave systems and design automation
Modeling appeared in both the plenary and technical sessions. The schedule included finite-element modeling of carbon-nanotube polymer composites, modeling of total ionizing dose effects in enclosed-layout transistors, and analytical study of plasmonic enhancement. A plenary talk addressed design automation for micro-electro-mechanical systems.
Other sessions explored microwave and millimeter-wave circuits and systems, including microwave devices made with liquid metal and 3D printing, wafer-level packaging of GaN/Si surface acoustic wave filters, and antenna design. A plenary presentation examined zero-power millimeter-wave wireless sensors. These subjects represent different approaches to device design and wireless sensing; the program did not specify industrial deployments or performance comparisons.
For engineers evaluating new technologies, the combination of modeling, fabrication and measurement topics provides context for how research progresses from analysis toward experimental investigation. The program also included work on power supply duty cycling for constrained IoT devices, another area related to designing electronic systems with limited energy resources.
What the program means for automation professionals
CAS 2018 was a broad microelectronics and microsystems meeting, not an industrial automation trade show. Its value to automation professionals lies in the underlying technologies represented across the sessions:
- Sensing: MEMS, temperature, electrochemical and wireless sensing research.
- Electronics: integrated circuits, power devices and signal-supporting components.
- Integration: packaging, heterogeneous system integration and microsystem assembly.
- Engineering methods: modeling, simulation, testing and fault assessment.
These areas can inform technical discussions about component development and system architecture, while the individual research presentations should be understood within their stated scope.
Conclusion
The CAS 2018 conference program mapped a wide research landscape spanning semiconductor devices, integrated circuits, microsensors, energy harvesting, environmental monitoring and microwave systems. For automation engineers, its practical takeaway is the importance of viewing sensing and control electronics as integrated systems: device characteristics, circuit design, packaging, power and reliability all contribute to how a technology can be incorporated into a larger application. The program documented research directions rather than validated factory solutions, but it provides a clear view of the technical foundations being explored across microelectronics and microsystems.