Access Official Technical PDF

Share Summary:LinkedInEmail

As power electronics move to silicon carbide (SiC) and gallium nitride (GaN), faster switching transitions place greater demands on the surrounding passive components. Capacitors must support high ripple currents and operating temperatures while keeping parasitic inductance low. CeraLink capacitors are designed for these conditions, combining a specialized ceramic material with a compact construction for use in demanding power circuits.

Understanding their behavior is important when selecting capacitors for a DC link, snubber, filter or flying-capacitor position. Their capacitance response to DC bias differs from that of many conventional multilayer ceramic capacitors (MLCCs), so component selection and circuit evaluation should reflect the actual operating point.

Why wide-bandgap switching changes capacitor requirements

SiC and GaN devices can switch rapidly, making the electrical characteristics of the complete commutation loop important to power-converter design. Excessive parasitic inductance can contribute to voltage overshoot during switching. A compact, low-inductance layout helps limit that effect and supports fast transitions.

At the same time, power-electronics designs are often expected to become smaller and operate at higher temperatures and frequencies. Capacitors in these circuits may also face substantial ripple current. These requirements make it necessary to consider more than nominal capacitance: engineers must assess performance at the intended voltage, temperature and frequency, as well as the capacitor’s size and parasitics.

CeraLink capacitors and positive DC-bias behavior

A key distinction of CeraLink is its positive-bias behavior: capacitance increases as DC bias rises from 0 V toward the operating voltage. This differs from the capacitance-versus-voltage behavior engineers may be familiar with from common MLCC dielectric classes. The relevant design value is therefore not necessarily the capacitance measured at zero bias, but the capacitance available at the circuit’s operating voltage and temperature.

The technology uses an antiferroelectric ceramic material. TDK describes its capacitance density at the operating point as a principal advantage. That makes it especially important to evaluate the component under representative conditions rather than compare parts solely by nominal capacitance. The intended DC voltage, AC ripple, temperature and frequency all belong in the selection process.

For reference, the product information reports typical capacitance densities at DC-link voltage, 20 V RMS and 25 °C of 4.9 µF/cm³ for CeraLink, compared with 2.5 µF/cm³ for class II barium-titanate MLCCs and 0.7 µF/cm³ for MKP film capacitors. These figures describe the stated measurement conditions and should not be treated as a substitute for evaluating a specific circuit or part.

Electrical and thermal characteristics for fast-switching circuits

CeraLink is specified for operation at temperatures up to 150 °C, with low losses at high temperature and low leakage current. The product information also states that it does not exhibit thermal runaway. Self-heating is generally low; the material’s self-regulating behavior also means that heating helps bring the capacitor to a temperature at which it performs well.

Frequency behavior matters as well. The stated optimal frequency range is 100 kHz to 1 MHz. Low-loss copper electrodes and a construction suited to high-frequency operation contribute to low equivalent series resistance (ESR). Typical ESR at 25 °C and 1 MHz is given as 3 to 45 mΩ, depending on series and voltage class. Typical equivalent series inductance (ESL) is 2 to 4 nH, also depending on the series; a key-facts summary gives approximately 3 nH as a typical value.

The product material reports a typical current rating per capacitance at 100 kHz and 105 °C of 11 A/µF for CeraLink, compared with less than 4.5 A/µF for class II MLCCs and less than 1 A/µF for MKP film capacitors. Its stated basis is lower losses at high temperature and frequency. Actual current capability remains dependent on the selected part and its application conditions. Very high dV/dt ratios are also possible, while the reported operating temperature decreases as frequency rises.

Where the technology can fit

The combination of compact size, low ESL and high-temperature operation can suit applications where switching behavior and layout are key considerations. Potential roles include snubber, filter and flying capacitors in SiC- and GaN-based designs. The product information also identifies DC-link use and high-voltage designs, including 400 V and 800 V systems.

Listed application areas include:

  • Automotive: onboard chargers, DC-DC converters, auxiliary inverters for high-voltage compressors, pumps and heaters, and inverter power modules.
  • Industrial and energy systems: drive inverters, power converters, energy storage systems, solar inverters and power supplies such as UPS and isolated supplies.
  • Other demanding equipment: welding, traction, test and measurement, and power supplies for medical equipment.

In a wide-bandgap power module, a small capacitor can help create a low-inductance commutation loop. That layout can support fast switching transitions while helping keep voltage overshoots low. Faster transitions, in turn, are associated with lower switching losses in wide-bandgap power semiconductors. These are circuit-level outcomes: component selection must be considered alongside the module, interconnects and overall layout.

Practical selection considerations

Before choosing a part, verify capacitance at the actual DC operating voltage and temperature, not just at zero bias. Confirm the required ripple-current capability and frequency, and check the ESR and ESL values for the specific series and voltage class. Evaluate the full voltage and thermal conditions, including switching behavior and the physical commutation-loop layout.

Packaging is another design consideration. The portfolio includes 2220-format options, low-profile styles and flex-assembly versions, with different voltage ratings and capacitance configurations. The product information lists reflow soldering and automotive qualification based on AEC-Q200, as well as an IATF 16949:2016 quality management system. Engineers should confirm the exact qualification and assembly details for the selected part and project.

Conclusion

CeraLink capacitors address several challenges associated with fast-switching power electronics: high operating temperatures, ripple current, compact layouts and low parasitic inductance. Their positive capacitance response to DC bias and high-frequency characteristics distinguish them from conventional capacitor options, but also make operating-point evaluation essential. For engineers designing SiC and GaN converters, assessing capacitance, current, ESR, ESL and temperature together provides a more meaningful basis for determining whether the technology fits a particular circuit.

Access Official Technical PDF

About The Author