Access Official Technical PDF

Share Summary:LinkedInEmail

A well-designed CMOS image sensor power supply is central to reliable industrial machine vision. The supply must provide several voltage rails, bring them up and down in the required order, and limit noise on the rails most sensitive to disturbances. In compact cameras, efficiency matters too: power lost as heat can affect thermal performance in a space-constrained assembly.

These requirements make sensor power design more than a matter of selecting regulators with the right nominal voltage. Engineers must consider load current, output capacitance, voltage accuracy, noise, power sequencing, and how the stages work together. Three possible architectures—a discrete regulator board and two power-management IC (PMIC) approaches—illustrate the main design choices.

Why image sensor power rails need careful design

Many CMOS image sensors use three supply rails for analog circuitry, pixel or interface circuitry, and digital logic. Typical analog rails are 3.3 V; pixel or interface rails may be 3.3 V or 1.8 V; and digital rails are commonly 1.8 V or 1.2 V. The exact requirements depend on the sensor.

The rails do not all have the same noise sensitivity. The analog rail is generally the most sensitive, with the pixel rail also requiring attention. Digital rails are typically less sensitive. Large bypass capacitors may be placed near sensor supply pins to help improve noise performance, making regulator stability and the ability to drive substantial output capacitance important parts of component selection.

Current demand and capacitance can vary considerably between sensor families. For example, the evaluated PYTHON devices use up to 250 µF of bypass capacitance on their analog and pixel rails, while the listed IMX25X/26X rails use up to 22 µF on analog and interface supplies. The PYTHON 3000/5000 analog rail also has higher typical current consumption than the other example sensors. Designs therefore need to be matched to the selected sensor rather than treated as interchangeable.

CMOS image sensor power supply architectures

Discrete regulators for flexibility

A discrete design separates the conversion and regulation functions across several devices. In the described arrangement, a wide-input buck converter first steps an input such as 5 V, 12 V, or 24 V down to a 4 V intermediate rail. That rail feeds low-noise LDOs for the noise-sensitive analog and pixel or interface supplies. A separate LDO or low-voltage buck converter can supply the digital rail, and a sequencer controls the order in which the rails start and shut down.

This architecture can be configured for the PYTHON and IMX sensor families discussed in the application report, with component and sequencing adjustments where needed. Its modularity also allows engineers to test the first and second power stages separately. The board described supports output capacitors up to 250 µF and has a stated size of 25 mm × 24 mm, excluding test points.

One useful design choice is how to power the digital rail. Because that rail is less noise-sensitive, either an LDO or a buck converter may be suitable, subject to the sensor’s voltage and current requirements. The reported tests found that using a buck converter for the digital rail, instead of an LDO, improved whole-system efficiency in the evaluated discrete solution. The choice should still be checked against the specific design’s electrical and noise requirements.

PMIC-based designs

A second approach combines a first-stage buck converter with the TPS65000 PMIC and a separate sequencer. The PMIC provides a buck converter and two LDOs, which can supply the three rails for the PYTHON 300/500/1300 and IMX25X/26X examples. As with the discrete approach, the IMX configuration requires changes to voltage settings and power sequencing.

The third architecture uses the TPS650330-Q1, which integrates three buck converters and an LDO. In the described setup, one buck stage converts a higher input voltage to an intermediate rail, two buck outputs supply the digital and interface rails, and the LDO supplies the analog rail. The configuration is intended for the IMX25X/26X examples and uses register settings to set voltage and sequence requirements.

An integrated PMIC can consolidate regulation functions, while a discrete design offers separate component choices for individual rails. Neither approach removes the need to verify that each output meets the sensor’s voltage, current, capacitance, and startup requirements.

Sequencing, noise, and component selection

Power-up and power-down order are specified by the sensor and must be implemented deliberately. A sequencer can enable each regulator after a set delay; shutdown can follow a reverse order to help avoid latch conditions. In the discrete example, an LM3880 sequencer provides a 30 ms delay between rails. The TPS650330-Q1 configuration for the IMX sensor example uses 20 ms between rails during power-up and 4 ms during power-down.

When selecting regulators, engineers should assess more than nominal output voltage. Key checks include:

  • Input and output ranges: Confirm the regulator supports the system input and required rail voltage.
  • Current capability: Allow for each sensor rail’s specified load.
  • Output capacitance: Check regulator stability and startup behavior with the intended bypass capacitors.
  • Noise and PSRR: Give particular attention to analog and pixel or interface rails.
  • Voltage accuracy and startup: Verify tolerance, soft-start, and compatibility with the required sequence.

LDO soft-start and feed-forward capacitor choices can affect startup time, transient response, noise, and power-good behavior. These interactions matter when the regulator’s startup must fit within the sensor’s sequencing window. Likewise, the intermediate voltage in a multistage supply affects overall efficiency, so it should be evaluated as part of the complete power path rather than chosen in isolation.

Practical implications for camera designers

For industrial automation engineers and camera integrators, the first step is to translate the sensor specification into a rail-by-rail design: voltage, current, capacitance, noise sensitivity, and required timing. From there, compare a discrete implementation with an integrated PMIC approach, accounting for configuration needs and the ability to test or adjust individual stages.

Validate the assembled supply under the intended input and load conditions. Check rail order and shutdown behavior, startup with the actual output capacitors, and the efficiency implications of regulator choices. A supply that meets nominal voltage targets but ignores sequencing, noise, or capacitance can still be unsuitable for the sensor.

Conclusion

Industrial CMOS image sensor power design is a coordinated exercise in regulation, noise management, sequencing, and thermal-conscious efficiency. Discrete regulators can provide flexibility across multiple sensor families, while PMIC-based solutions integrate several power functions. The practical choice depends on the sensor’s specific rail requirements and the system’s configuration needs. Matching components to those requirements—and validating the complete power sequence and load behavior—provides a sound foundation for dependable machine vision cameras.

Access Official Technical PDF

About The Author