For industrial and building applications that need heat above domestic hot-water temperatures, conventional flat-plate collectors may not be sufficient. A CPC solar collector uses a shaped reflector to concentrate sunlight onto a receiver, offering a route to medium-temperature solar heat without relying on a sun-tracking system. A tested prototype combining a compound parabolic concentrator (CPC) with an evacuated tube illustrates both the design choices involved and the care needed when interpreting performance data.
Why concentrate solar heat?
Solar radiation is abundant, but its intensity at a collector surface is relatively low and varies with time and weather. Standard solar collectors can produce useful heat efficiently when operating temperatures remain well below water’s boiling point. When the target moves into the 80–250°C range, concentration can help raise working temperatures while maintaining useful thermal conversion.
Potential applications in this temperature range include absorption cooling and organic Rankine cycle power generation. These processes require heat at higher temperatures than typical domestic hot-water production, making collector design and receiver performance important considerations.
How a CPC solar collector captures sunlight
A CPC is a non-imaging concentrator: rather than forming a sharp image of the sun at a point or along a line, its reflector directs incoming rays onto a receiver with a defined shape and finite area. In the thermal prototype, that receiver is tubular. Multiple reflections within the reflector can guide rays toward the tube across a broad range of incident angles.
This wide acceptance range is a practical distinction from concentrators that need precise alignment. The prototype was designed to accept sunlight over an angle of about 31°, helping it capture radiation without a tracking system. A broad view of the sky can also allow some diffuse radiation to reach the receiver, although the contribution depends on operating and sky conditions.
Designing the reflector around the receiver
The shape of a CPC reflector depends on the geometry of its receiver. For a tubular absorber, the profile is calculated around a circular receiver rather than a flat target. In this case, the absorber coating was on the inner glass tube of a commercially available evacuated tube. The reflector design also accounted for the receiver’s position: the absorber was displaced 3.4 mm from the reflector’s theoretical bottom cusp.
The design balanced several constraints, including acceptance angle, reflector height and concentration ratio. A full-height concentration ratio of 2.0 was considered, but the reflector was truncated to half its full height to make the assembly more compact. Truncation reduces aperture and therefore concentration; the estimated correction factor was 0.87, giving an effective ratio below the full-height value.
Before thermal testing, the reflector profile was manufactured and checked in the laboratory using laser ray tracing. The tests showed rays entering at different positions and angles reaching the tubular target, including rays that underwent multiple reflections. This optical check supported the reflector design, while outdoor testing was needed to assess heat collection under operating conditions.
Receiver and outdoor test setup
The CPC was coupled to an evacuated tube consisting of coaxial glass pipes with an evacuated space between them. A selective absorber surface on the inner tube converted incoming radiation to heat. A U-shaped copper pipe, held in thermal contact with the absorber by springs, transferred heat to circulating water.
The prototype was tested outdoors using an approach based as far as possible on the Outdoor Steady-State (OSS) method in EN 12975-2. Measurements included solar irradiance, inlet and outlet fluid temperatures, flow rate and ambient temperature. The collector’s instantaneous efficiency was calculated as useful heat extracted divided by solar energy incident on its aperture area.
There were departures from the standard test conditions. For example, the test setup held inlet temperature approximately constant and varied mass flow rate, whereas the standard method specifies a constant flow rate and variation of inlet temperature. Some test points also had diffuse irradiance above the stated OSS limit, and one had global irradiance below the specified threshold. The investigators examined the available data and included the full set in their analysis.
What the efficiency results show
The measured efficiency data were related to reduced temperature difference: the difference between the mean heat-transfer-fluid temperature and ambient air temperature, divided by solar irradiance. The results produced a linear efficiency curve, with a zero-loss efficiency of 0.5882 and a temperature-related coefficient of 2.571 in the study’s formulation. A quadratic term was not statistically significant for this data set.
The prototype’s efficiency was relatively steady across the tested operating range, consistent with the evacuated receiver’s high level of thermal insulation. However, measurement uncertainty matters when using the curve. At high reduced temperature differences, low flow rates were needed, bringing flow measurement closer to the lower end of the meter’s range and increasing uncertainty in calculated useful output.
Why steady-state results need careful application
An OSS efficiency curve describes performance under near-steady test conditions. When the researchers compared its predictions with measurements collected over a day, predicted thermal output was consistently higher than measured output. The steady-state curve therefore did not reliably represent daily operation on its own.
Several effects can contribute to this gap. A concentrating collector’s response changes with the incidence angle of direct sunlight, and its performance under diffuse radiation is influenced by concentration. The collector’s thermal capacity can also affect its behavior over longer periods, but is not represented in the basic steady-state approach. The study consequently points to the Outdoor Quasi-Dynamic method as more appropriate for capturing transient behavior.
Practical implications for system design
For engineers and system integrators evaluating medium-temperature solar heat, the prototype demonstrates that reflector geometry, acceptance angle, truncation and receiver placement must be considered together. Optical ray tracing can verify whether a proposed profile directs rays onto its intended target, but it does not replace thermal testing.
Performance data should also be matched to the intended use. A steady-state efficiency curve can characterize operation under specified conditions, yet daily energy estimates may need to account for changing incidence angles, diffuse radiation and thermal response. Understanding the test method and its limits is essential when translating collector ratings into operating expectations.
In practice, CPC technology offers a way to combine a tubular evacuated receiver with a reflector that accepts sunlight over a broad angular range. The reported prototype achieved a measured efficiency curve under outdoor testing, while its daily comparison showed why transient effects cannot be ignored. For project decisions, both the collector’s optical design and the suitability of its performance model should be assessed against the application’s operating profile.