Deep UV LEDs can provide compact ultraviolet sources for applications such as disinfection, biochemical detection and spectroscopy. But producing useful light in the 200–300nm range is challenging: efficiency is low, and the high-aluminium-content AlGaN materials used in these devices are difficult to grow with few defects. Research reported in 2019 explored several ways to address these barriers, from improving electrical contacts to changing how light escapes from a device.
These approaches target different parts of the LED system. Some aim to improve photon extraction; others focus on crystal quality or on limiting light absorption within the device. Together, they illustrate why deep UV LED development involves both semiconductor materials engineering and device design.
Why deep UV LED performance is difficult to improve
AlGaN is used to produce ultraviolet emission, but growing it on sapphire presents challenges. Differences in lattice spacing and thermal expansion between the substrate and semiconductor can introduce strain and defects. These defects can reduce the efficiency with which injected carriers produce light.
Light extraction is another constraint. At semiconductor-to-air boundaries, a large refractive-index difference can cause total internal reflection, trapping photons inside the device. Electrical design matters too: contact layers must provide a workable current path without absorbing too much of the ultraviolet emission. The reported studies addressed these issues through distinct structures and fabrication methods.
Reflective electrodes balance contact quality and light output
For a 280nm AlGaN LED, researchers investigated a chromium/aluminium (Cr/Al) n-type electrode. Aluminium reflects ultraviolet light, while chromium helps form an ohmic contact with the high-aluminium-content n-AlGaN layer. The trade-off is that chromium absorbs deep UV radiation, so its thickness can affect both electrical contact and optical performance.
The devices used a flip-chip arrangement, directing much of the emitted light through the sapphire substrate. This is useful because the p-GaN contact layer absorbs deep UV light. In tests, the device with a 1nm chromium layer produced the highest light output at a given injection current among the reported devices. At 180mA, its output was 40.9% higher than that of the device with a 20nm chromium layer. The 1nm chromium device also had a peak external quantum efficiency 25.4% higher than the thickest-chromium device.
Electrical performance did not follow exactly the same pattern: a 2.5nm chromium layer gave the lowest turn-on voltage and contact resistance. The result highlights a practical design consideration: optimizing a reflective contact means balancing optical reflectivity against reliable ohmic contact formation.
Graphene-assisted AlN growth targets crystal quality
A separate approach used a graphene interlayer on nano-patterned sapphire to improve the growth of aluminium nitride (AlN), a template material for AlGaN LEDs. In this work, plasma treatment introduced defects into the graphene surface to support AlN nucleation. The researchers proposed that aluminium atoms could bind at these sites while moving more freely across other parts of the graphene, encouraging faster, more uniform growth.
Compared with AlN grown directly on the patterned sapphire, the graphene-assisted layer coalesced into a continuous, flatter surface. X-ray measurements showed lower peak widths associated with AlN crystal planes, and the researchers estimated reduced screw and edge dislocation densities. Measured biaxial stress also decreased. An LED made using the graphene-based template showed a 280nm electroluminescence peak around 2.6 times that of a device grown on patterned sapphire without graphene, at the reported 40mA injection current.
This method addresses the material template before the LED layers are formed. Better control of epitaxial growth can therefore complement device-level measures such as electrode design.
Nanowires and surface texturing improve light extraction
AlGaN/GaN core-shell nanowires
Researchers also reported near-UV LEDs built from AlGaN shells around GaN nanowire cores. The devices emitted near 365nm. Compared with the group’s GaN/GaN nanowire reference devices, the AlGaN/GaN structures had around five times the integrated electroluminescence intensity for a given current injection.
The wider-bandgap AlGaN shell can help limit absorption of light emitted by the GaN core, while also acting as an electron-blocking structure. However, the AlGaN/GaN devices had a higher turn-on voltage than the GaN/GaN comparison devices. The researchers also observed increased emission and lower series resistance after prolonged current injection, which they associated with an electrical annealing effect on the p-contact. Contact metallization and annealing were identified as areas for further development.
Nanodomes on a thin-film LED surface
For near-UV LEDs emitting around 370nm, another team structured the exposed n-AlGaN surface into nanodomes. The devices were flipped onto a supporting wafer and the original silicon growth substrate was removed before the surface patterning process. This made it possible to texture the thicker n-side layer rather than risk damaging the thin p-side or the active quantum wells.
In the reported devices, nanodomes with a height-to-diameter ratio of 0.27 produced integrated electroluminescence 3.9 times that of flat reference devices. The current-voltage characteristics were almost identical, indicating that the surface treatment improved light output without a reported change in those electrical characteristics. The researchers linked the improvement to reduced trapping of light at the semiconductor surface.
Practical implications for UV LED development
The studies show that there is no single route to better ultraviolet LED performance. Engineers and device developers can consider several distinct levers:
- Contact design: tune reflective metal stacks to balance ultraviolet reflectivity with low-resistance electrical contact.
- Template engineering: use approaches such as graphene-assisted AlN growth to improve layer uniformity and reduce defects and stress.
- Device architecture: explore nanowire heterostructures where emission, absorption and carrier injection can be managed through the core-shell structure.
- Surface geometry: texture an appropriate semiconductor surface to help photons escape without compromising sensitive device layers.
These results come from different wavelengths, materials and device configurations, so they should not be treated as directly interchangeable performance benchmarks. Their broader value is in showing how optical, electrical and epitaxial decisions interact. For industrial applications, the relevant design choice depends on the target wavelength and the device structure, as well as the specific performance constraint being addressed. Continued progress in deep UV LEDs will depend on improving material quality and electrical behavior while giving generated photons a more effective path out of the device.