The FUSB307B USB Type-C port controller brings connector detection, USB Power Delivery (USB-PD) protocol handling and power-path control together in a device designed to work with a Type-C Port Manager (TCPM). For automation and embedded-system designers, its central architectural role is to take on time-sensitive port tasks while the system processor manages policy and broader product behavior.
This division of responsibility matters in designs that need to detect attachment and orientation, negotiate power, or support dual-role operation. The FUSB307B provides the hardware interface and autonomous functions; the TCPM communicates with it over I2C and makes system-level decisions.
How the FUSB307B USB Type-C port controller divides the work
The controller monitors the connector’s Configuration Channel (CC) pins, CC1 and CC2. These pins help identify connection state and plug orientation, and support USB-PD communication using BMC signaling. Depending on the port’s role, CC signaling also indicates the current available for a sink or enables a source to detect an attached device.
The TCPM configures port behavior and responds to events through the controller’s I2C register interface. An active-low interrupt output, INT_N, signals when an event needs processor attention. This allows the controller to handle selected protocol steps locally while firmware remains responsible for policy and subsequent actions.
Examples of autonomous functions include responding to valid received packets with GoodCRC, retrying certain transmissions when an expected GoodCRC is not received, and optionally toggling between source and sink terminations for dual-role operation. The controller supports USB-PD features including Fast Role Swap, Sink Transmit and chunked extended data messages, subject to the device’s documented operation and the system’s TCPM implementation.
Type-C detection and dual-role port operation
For attachment management, the TCPM can configure Rp or Rd terminations directly, or enable the FUSB307B’s automatic dual-role port (DRP) toggling. In DRP mode, the controller alternates between source and sink presentations while looking for a partner. Once it detects a potential connection, it stops toggling and reports the connection result and CC-pin status to the TCPM.
The controller filters CC changes before reporting them, but system firmware must still follow the Type-C specification’s required debounce behavior. After an interrupt, the TCPM reads status registers, determines the appropriate role and orientation, and configures related functions such as VCONN and the selected power path.
This arrangement is useful when a design needs flexible port roles without delegating product policy to the port controller. It also makes the firmware sequence an important part of integration: the host must interpret status, configure the port, and coordinate power delivery with the rest of the system.
USB-PD messaging and power-path control
The FUSB307B includes a USB-PD physical layer and packet buffers. The TCPM prepares outgoing messages in registers and starts transmission through the transmit control register; received messages are made available for the host to read. Automatic GoodCRC handling reduces the need for the processor to meet the immediate response timing of every valid packet.
USB-PD can support power negotiation and role swaps, as well as communication associated with supported alternate interfaces, accessories and full-featured cables. The controller does not replace the TCPM’s policy role: firmware must decide which messages to send, manage the contract and respond to reported events.
Two outputs control external VBUS switching: SRC for the source path and SNK for the sink path. The controller can also monitor VBUS presence and measure its voltage with an onboard 10-bit ADC. Programmable voltage alarms can report threshold crossings to the host, while discharge functions support controlled reduction of VBUS in relevant operating conditions.
Designers should distinguish between the controller’s control signals and the external power circuitry. SRC and SNK command external load switches; system power components and TCPM policy determine how the complete source or sink path is implemented. The device also supports manual and automatic discharge behavior, so register configuration and disconnect handling should be reviewed against the intended power architecture.
Dead-battery startup and system integration
Dead-battery operation is a notable feature for battery-powered equipment. When VDD is absent but VBUS is present, the FUSB307B can power from VBUS, continue presenting Rd and provide an LDO output to support a microcontroller or TCPM during startup. Once VDD reaches the specified operating condition, the device switches from VBUS power to VDD and bypasses the LDO.
That sequence can allow the system to begin managing a connected Type-C source before its main battery-powered circuitry is available. In multi-port systems, the TCPM can decide which sink path to enable. The controller’s role is to support startup and port control; the surrounding design must still coordinate charging, system power and port selection.
Other integration points include the open-drain I2C and interrupt signals, selectable I2C addresses, programmable GPIOs, orientation output and VCONN switching. The FUSB307B’s VCONN switch routes its regulated input to the appropriate CC pin to power supported cables or accessories. Engineers should consult the full device documentation for electrical limits, register behavior, initialization sequences and component-level implementation details.
Practical implications for design teams
The FUSB307B is best understood as a port-control building block rather than a complete USB-C power-management solution. It combines Type-C detection, USB-PD communication support, VBUS monitoring and source/sink control interfaces, while leaving policy and system coordination to the TCPM and host firmware.
For design teams, the practical task is to define that boundary clearly. Map interrupt and I2C handling, configure role-detection behavior, coordinate external power switches, and validate voltage monitoring and discharge settings for the intended use case. With those responsibilities assigned, the controller’s autonomous timing functions and dead-battery support can be integrated into a broader Type-C system design without confusing protocol assistance with system-level decision-making.