GaN power amplifiers can help address a central challenge in Ku-band satellite communication: delivering enough transmit power for a useful link without making a very small aperture terminal (VSAT) excessively large, heavy or power-hungry. A developed transmitter architecture combines gallium nitride high-electron-mobility transistor (GaN-HEMT) amplifiers with a block up-converter (BUC), and evaluates the system using modulated signals and a satellite link.
The engineering results illustrate how amplifier design involves more than maximising peak output. Frequency coverage, power-added efficiency (PAE), signal linearity, thermal behaviour and integration all affect whether a power stage is suitable for a practical transmitter.
Why GaN-HEMT technology matters for VSAT transmitters
A satellite uplink must overcome the substantial free-space attenuation between a ground terminal and a satellite. Increasing antenna gain can improve the link, but a larger antenna may make a compact terminal impractical. Raising BUC output power is another option, though it can increase equipment size, weight and power consumption.
GaN-HEMT technology offers a way to develop high-power solid-state amplifier stages for this application. The work described here uses bare-die devices in hybrid microwave integrated circuits (MICs) built on alumina substrate. Instead of relying on a single amplifier configuration for every operating condition, it develops separate designs for different parts of the Ku-band and for wider frequency coverage.
GaN power amplifiers: output, efficiency and bandwidth
Three amplifier designs demonstrate the trade-offs involved in selecting a Ku-band power stage:
- Upper Ku-band: A two-stage design using two 250 nm GaN-HEMT bare-die devices provides about 15 dB saturated gain across 13.75–14.5 GHz. Under continuous-wave (CW) excitation, it produces more than 50 W with PAE above 23%. With QPSK modulation, measured average output exceeds 30 W, with 70 W peak output and 21% PAE, while meeting the stated Eutelsat linearity requirements.
- Lower Ku-band: A separate design for 12.75–13.25 GHz delivers more than 80 W for pulsed RF signals, with PAE of at least 34%. This is a pulsed result and should not be treated as a continuous-wave rating.
- Extended Ku-band: A broadband design covering 12.75–14.5 GHz produces more than 55 W with 20% PAE. Its 14% fractional bandwidth spans both uplink frequency bands, but the wider coverage comes with lower efficiency than the narrower-band approaches.
These results show why a PA specification should be read in context. Output power figures depend on whether the signal is CW, pulsed or modulated, while the usable average power for a modulated waveform may be lower than its peak. Likewise, a design that covers a wider band may be useful for equipment flexibility, but broadband matching can constrain achievable performance.
Linearity for digitally modulated satellite signals
Power amplifiers are nonlinear as they approach compression. For digitally modulated signals, this can distort signal amplitude and phase and cause spectral regrowth: energy spreads beyond the intended channel into adjacent frequencies. The effect matters for schemes such as QPSK and 8PSK, as well as higher-order modulation formats used in DVB-S2X, including 16APSK and 32APSK.
The BUC incorporates an active linearisation technique that adjusts the transmitter response to improve spectral regrowth for common modulation schemes. The approach was also evaluated with higher-order formats. This is important because modulation formats with more complex symbol arrangements place different demands on signal fidelity; a power stage must be considered as part of the complete transmit chain, not just as a source of RF watts.
For system integrators and equipment designers, the practical implication is to assess linearity at the intended operating point and with the intended waveform. A CW saturation result alone does not establish performance under a particular modulation, output back-off or spectral mask requirement.
Integrating the amplifier into a block up-converter
A BUC translates an intermediate-frequency signal to the satellite uplink band and provides the transmit amplification needed at the terminal. The developed BUC integrates frequency-generation and conversion functions with either a 10 W or 50 W amplifier option. The design goal is a compact, low-weight assembly with low dissipated power, alongside the active linearisation function.
Integration creates system-level design considerations beyond the PA itself. The local oscillator and conversion chain must support the required RF output, while filtering, power conversion, biasing and thermal behaviour all contribute to the finished unit. The project also examined BUC operation with different modulation schemes and assessed temperature behaviour, reflecting the need to verify an integrated transmitter rather than assume that component-level measurements tell the whole story.
From component measurements to a satellite link
Evaluation extended beyond amplifier and BUC measurements to a VSAT satellite-link test. The BUC operated in the link and demonstrated transmit data rates of up to 1 Mbit/s. This system-level step helps establish that the transmitter can function within a complete communications path, where the outcome depends on more than amplifier output alone.
Link planning still requires attention to the antenna, frequency plan, modulation and coding choices, and the overall link budget. The reported data rate is evidence of demonstrated operation in the tested setup, not a universal throughput expectation for every VSAT deployment.
Practical implications for RF system designers
When selecting or developing a Ku-band transmitter, technical teams should match the amplifier architecture to the operating requirements. Key questions include:
- Is coverage needed across one uplink band or across both bands?
- Does the application require CW, pulsed or modulated output performance?
- What average power and linearity are required for the chosen waveform?
- How do efficiency, thermal dissipation, size and weight constrain the terminal?
- Has performance been verified at both component and system level?
GaN-HEMT power amplifiers provide a route to high-output Ku-band solid-state transmission, but their value depends on how well the amplifier, linearisation and BUC are matched to the link. The demonstrated designs make the trade-off clear: narrower-band stages can prioritise output or efficiency, while broad coverage supports frequency flexibility with a different performance balance. For VSAT designers, evaluating the complete transmitter under realistic modulation and link conditions is essential to turning device-level capability into a practical satellite terminal.