As high-data-rate payloads place greater demands on onboard data handling, the links between satellite subsystems become an important part of system design. Intra-satellite optical communication offers an alternative to electrical cable links by carrying data as light through fiber. A prototype transceiver card illustrates how an FPGA, optical transceivers and supporting interfaces can be combined to build and test this type of link.
The design addresses a practical engineering question: how can subsystems exchange data over a fiber channel while retaining programmable data generation and acquisition for evaluation? Its hardware combines optical and LVDS interfaces on a multilayer printed circuit board (PCB), creating a platform for checking transmission and reception between two systems.
Why consider fiber for onboard data links?
LVDS and serializer/deserializer (SerDes) links are established options for high-speed data transfer. LVDS uses differential signaling and is used in onboard data-handling applications. However, electrical cabling can add weight and remains susceptible to electromagnetic interference. Fiber provides a different transmission medium: signals travel as light, and the fiber is immune to electromagnetic interference. It also offers low signal loss over the short distances typical of connections within a spacecraft.
Fiber links also provide galvanic isolation and can be lightweight and mechanically flexible. These characteristics can be useful when connecting equipment that must meet constraints on mass, volume and electromagnetic compatibility. The choice is not without trade-offs: optical communication requires electro-optical conversion at the transmitter and opto-electrical conversion at the receiver, bringing an associated power penalty. Component suitability and space heritage also need consideration in mission-level decisions.
Intra-satellite optical communication card architecture
The prototype card is designed to test communication between two systems. An FPGA acts as the data-generation and acquisition element, while optical transceivers convert between electrical signals and optical data. The card also includes buffers, LVDS transmit and receive interfaces, clock sources, power regulation, a power-on-reset circuit and an RS232 port for communication with a PC.
Two transceiver types are provided for evaluation: three FTLF1421P1WCL SFP transceivers, specified in the design for bidirectional links up to 2.67 Gb/s, and two VTT SPFI-003-6G transceivers for full-duplex operation up to 6.25 Gb/s over short-distance links. These are component specifications in the prototype design, not a claim that every configured link achieves those rates.
The power input is 5 V DC. Low-dropout regulators derive 3.3 V for logic and 1.5 V for the FPGA core. A power-on-reset circuit is intended to bring the system into a consistent startup condition. Clocking can be provided by a crystal oscillator or a 250 MHz LVDS crystal oscillator. Buffers and LVDS interfaces provide additional signal access alongside the optical paths.
PCB stack-up and signal integration
The card uses an eight-layer PCB stack-up with signal, ground and power layers separated by dielectric and prepreg materials. The design selected eight layers after a six-layer version resulted in an impedance mismatch. Layer arrangement and component placement matter because they affect signal routing and the board’s ability to manage noise and interference. The PCB brings the FPGA, optical components and electrical interfaces together for testing without making the fiber link itself the only point of access.
How the data path was tested
The demonstration setup connects a development board to the designed PCB through optical fiber. The development-board FPGA generates test patterns, including up-counters, down-counters and random values. The transmitted data is organized into frames, encoded using 4B5B, and serialized in the FPGA before being sent to the optical transceiver.
In 4B5B encoding, each group of four data bits is mapped to a five-bit code. The added bit helps address the receiver’s clocking needs. At the receiving end, the optical transceiver converts the incoming light pulses back into electrical signals. The FPGA then converts the serial stream to parallel data and reverses the 4B5B mapping.
After decoding, the receiving logic removes the protocol header, sequence number and inter-frame gap to recover the message. The resulting eight-bit parallel data passes through a buffer and exits through a 50-pin connector to a data acquisition unit, which records the output in a text file. Comparing the transmitted and received data showed matching results for the tested patterns.
What the prototype demonstrates
The test establishes a useful end-to-end workflow for evaluating an optical data link: generate known patterns, frame and encode them, transmit over fiber, decode at the far end, and compare the recovered message with the original. Including both optical transceivers and LVDS interfaces on the same card also provides flexibility for testing different signal paths.
For engineers assessing similar architectures, the prototype highlights several design considerations:
- Define the link requirements: Data rate, distance, power, mass and electromagnetic compatibility all influence interface selection.
- Plan clocking and encoding: The transmitter and receiver must agree on framing and encoding so the data can be recovered correctly.
- Design the PCB as part of the signal path: Layer stack-up, impedance and component placement are relevant to reliable high-speed operation.
- Verify with known data: Comparing transmitted and received patterns provides a direct check of the complete transmission and reception chain.
Practical implications
The optical transceiver card demonstrates that an FPGA-based, fiber-linked architecture can be assembled and tested for communication between satellite subsystems. Matching transmitted and received data confirms successful operation for the patterns used in the reported hardware test; it does not, by itself, establish performance under every mission condition.
For technical decision-makers, the broader lesson is to evaluate the complete link rather than the fiber or transceiver in isolation. Data formatting, clock recovery, electrical interfaces, power regulation and PCB implementation all contribute to the system. A prototype that exposes these elements can help teams assess whether intra-satellite optical communication is an appropriate approach for their onboard data-handling needs.