High-resolution Earth-observation missions, including synthetic aperture radar (SAR), can generate more data than conventional satellite downlinks can efficiently return. A demonstrated X-band satellite downlink addressed this challenge by transmitting 2.65 Gbps from the RAPIS-1 small satellite. The system combined two circular-polarization channels with 64APSK modulation, a 300 Msps symbol rate and DVB-S2X framing and coding.
Achieving that rate required more than selecting a dense modulation scheme. The transmitter, onboard antenna, propagation path, ground-station antenna and demodulator all had to preserve signal quality. The system’s practical lesson for high-throughput links is that spectral efficiency depends on managing distortion and interference across the complete communications chain.
How polarization multiplexing increased downlink capacity
The system carried independent data on right-hand circular polarization (RHCP) and left-hand circular polarization (LHCP). Using both polarizations allows two channels to share the same frequency band, rather than assigning separate frequency bands and losing capacity to guard bands. Each channel used 64APSK with a coding rate of 4/5.
At 300 Msps, the combined channels delivered 2.65 Gbps within an occupied bandwidth of 315 MHz. That corresponds to a reported spectral efficiency of 8.41 bit/Hz. The waveform used a roll-off factor of 0.05, which helps limit the bandwidth occupied around the modulated signal.
Higher-order modulation packs more information into each symbol, but it also makes signal quality more demanding. Distortion, noise and leakage from the opposite polarization can interfere with symbol decisions. The design therefore paired 64APSK with measures to control amplifier nonlinearity and polarization crosstalk.
Managing transmitter distortion and spectral constraints
The onboard transmitter used a gallium-nitride high-power amplifier (HPA). Because amplifier nonlinearity can distort a constellation and increase out-of-band emissions, the team adjusted the HPA bias conditions and input power to improve its AM-AM behavior while maintaining an average RF output power of 29.5 dBm per channel. The reported third-order distortion was suppressed to approximately 30 dB below the in-band level.
That spectral control mattered because the allocated Earth-observation downlink band was adjacent to a protected deep-space band. The system used a band-pass filter (BPF) to further attenuate out-of-band emissions. The selected occupied bandwidth and 300 Msps symbol rate were designed around the filter’s group-delay characteristics and the need to protect the neighboring band.
For engineers evaluating a high-rate transmitter, this illustrates a key trade-off: operating an HPA in a way that supports a clean high-order constellation must be balanced with emission limits and the filtering required by the frequency plan.
High-XPD antennas limit polarization crosstalk
Polarization multiplexing only works effectively when the RHCP and LHCP channels remain sufficiently distinct. Cross-polarization discrimination (XPD) measures the power ratio between the intended polarization and the unwanted cross-polarized component. Low XPD can introduce interference that degrades demodulation, particularly with a high-order modulation format.
The onboard dual-polarized antenna combined a corrugated horn with a septum-type polarizer. Measurements showed XPD of 37–43 dB across the target X-band range of 8.025–8.34 GHz. The ground station was upgraded with a replacement primary radiator and a polarizer, achieving XPD above 37 dB.
Atmospheric conditions also affect polarization separation: rain and ice in clouds can reduce XPD. The system design therefore considered antenna performance together with propagation effects. Its calculated total XPD, including atmospheric effects, was greater than 27 dB under the specified system conditions. This is why antenna XPD cannot be treated as an isolated component specification when planning a polarization-multiplexed link.
Ground-station noise performance and signal processing
The receiving system used a modified 10 m ground-station antenna. Its polarizer and low-noise amplifiers were placed in a cryogenic chamber and cooled to reduce thermal noise. At a 90-degree elevation angle, the reported system noise temperature was 58 K maximum, and the antenna’s gain-to-system-noise-temperature ratio (G/T) was 39 dB/K.
Because a real-time DVB-S2X demodulator for the required 300 Msps rate was not available for the demonstration, the received signals were recorded at the antenna site and decoded later with a software demodulator. Its processing included frame detection, carrier-frequency-offset compensation, channel equalization and LDPC error correction, with BCH decoding also used when needed. Pilot symbols in the DVB-S2X frame supported channel estimation and equalizer updates.
This non-real-time approach separated signal capture from computationally intensive decoding. It also provided a way to assess the downlink data without implying that the complete decoding chain operated in real time.
In-orbit demonstration and engineering implications
The system flew on RAPIS-1, launched in January 2019. During the in-orbit demonstration, the RHCP and LHCP signals were recorded and decoded. The recovered binary data matched the transmitted data for the reported downlink, demonstrating a combined rate of 2.65 Gbps using 64APSK at 300 Msps.
For satellite and ground-system designers, the result underscores several connected design priorities:
- Coordinate the link as a complete system. Modulation, HPA operating point, filtering, antenna XPD, receiver noise and demodulation all influence usable throughput.
- Protect polarization isolation. High-XPD antennas at both ends help limit crosstalk, while atmospheric effects must also be considered in the link budget.
- Account for adjacent-band requirements. Out-of-band emissions and filter behavior can constrain symbol rate and occupied bandwidth.
- Match receiver processing to the waveform. High symbol rates and DVB-S2X coding require suitable capture, synchronization, equalization and decoding capability.
The 2.65 Gbps demonstration shows how polarization multiplexing and 64APSK can raise the capacity of an X-band Earth-observation link, provided the surrounding RF and ground infrastructure are engineered to support them. For industrial and technical decision-makers assessing similar high-throughput systems, the practical takeaway is to optimize the transmitter, antennas, propagation margin and receiver together—not as separate subsystems.