High-frequency copper-clad laminate (CCL) is a foundational material for circuit boards used in next-generation communications. As systems move into millimeter-wave bands, the insulating materials in a board can have a greater effect on signal loss and delay. For automation engineers, system integrators, and equipment designers, understanding this material shift helps clarify why conventional board constructions may not suit every high-speed application.
The change is tied to growing demand for connected devices and higher-volume data services. The 2019 outlook discussed here anticipated expanding use of high-frequency communication in applications including base stations, servers, automotive radar, and satellite communications. Its market forecasts were projections made at that time, rather than present-day measurements.
Why higher communication frequencies change material requirements
Higher frequencies can support more information transfer per unit of time, enabling high data rates and high-capacity connections. They also present propagation challenges. Compared with lower-frequency radio waves, millimeter waves generally travel shorter distances, diffract less readily, and are more difficult to pass through materials. These constraints can affect network coverage and make antennas and their supporting materials especially important.
For circuit designers, one key issue is transmission loss within the antenna and its circuits. A substrate’s dielectric properties influence signal behavior: the source identifies dielectric loss as an important factor in antenna and circuit performance. As operating frequencies rise, the choice of insulating resin and other substrate components therefore becomes a design consideration, not just a procurement detail.
How high-frequency copper-clad laminate supports circuit performance
Rigid CCL is a printed-circuit-board material made from copper layers and an insulating resin. Some constructions impregnate glass fiber with resin, while others combine resin with ceramic materials. The material stack forms the base for patterned conductive circuits, so its electrical characteristics can influence how signals travel through the finished board.
In the 2019 presentation, epoxy-based compositions were described as unsuitable for some next-generation communication applications above 24 GHz, with polyphenylene ether (PPE) and fluorinated resin identified as alternatives. The underlying engineering principle is to select a substrate system that helps limit signal loss at the intended operating frequency. Material selection must still be assessed in the context of the complete board and application.
Material properties are part of a wider design problem
Low-loss substrates are one element in a broader high-frequency design. Antenna performance, circuit layout, fine patterning, component placement, and manufacturing control also matter. The source highlights the need for more precise patterning and mounting as electronic elements become smaller and more complex. That means material suppliers and board manufacturers need capabilities that extend beyond providing resin or copper-clad stock.
For example, composite development may involve combining fluorinated resin with inorganic fillers such as ceramics or glass. Characterization can include dielectric properties, thermal expansion, peel strength, thermal conductivity, and transmission loss. These measures help establish whether a material and process are appropriate for the intended board design.
Why manufacturing and interface control matter
CCL production involves more than choosing a resin family. The source describes capabilities such as resin-and-filler compounding, sheet production, interface analysis, and manufacturing processes including roll-to-roll processing and vacuum heat pressing. Each step contributes to the consistency and performance of the resulting laminate.
Adhesion is another consideration when combining fluorinated materials with other components. The 2019 material describes a fluoropolymer formulation intended to add adhesive properties while retaining characteristics associated with fluorinated resin. In practical terms, engineers evaluating a laminate should consider how its layers bond and behave together, alongside electrical performance. The source does not imply that a single material solves every design or manufacturing challenge.
Applications across communications and industry
High-frequency rigid CCL is relevant to several types of equipment identified in the source:
- Communication infrastructure: Base-station antennas and related equipment operating at higher frequencies.
- Servers and routers: High-speed systems where board materials are part of the signal path.
- Automotive systems: Millimeter-wave radar applications.
- Satellite communications: Equipment requiring high-frequency circuit materials.
The broader communication-material landscape also includes antennas integrated with glass. The source describes glass-based approaches for building windows and vehicles, as well as synthetic fused silica selected for its lower dielectric loss than ordinary glass. These examples reinforce a wider point: high-frequency system design spans the antenna, its substrate, the surrounding structure, and the communication environment.
Practical considerations for engineering teams
When assessing materials for a high-frequency PCB or antenna assembly, teams can use a structured review:
- Confirm the operating frequency and the application’s signal-loss requirements.
- Compare candidate resin systems and substrate dielectric characteristics.
- Review the construction, including copper layers, reinforcement, and fillers.
- Evaluate manufacturing and interface-control requirements, not only the base material specification.
- Consider how the board integrates with the antenna, enclosure, glass, or other surrounding materials.
These checks help align material selection with the complete electrical and manufacturing design. A laminate suitable for one frequency range or product may not automatically meet the needs of another.
Conclusion
The move to higher-frequency communications raises the importance of low-loss circuit-board materials. High-frequency copper-clad laminate combines conductive copper with insulating materials selected for demanding signal paths, while its performance depends on resin choice, composite design, interfaces, and production control. For industrial and communications equipment teams, the practical takeaway is to evaluate CCL as part of the full antenna and circuit design—not as an interchangeable board commodity.