Access Official Technical PDF

Share Summary:LinkedInEmail

Industrial soft starter selection starts with the motor and driven load—not simply the kilowatt value on a motor nameplate. Starting severity, required stopping behavior, operating conditions, and the electrical installation all affect which device is suitable. A structured approach helps engineers and system integrators match the starter’s capabilities to the application while avoiding sizing assumptions that can lead to unsuitable operation.

Match the soft starter to the load

A soft starter controls the motor’s start, and, depending on the device, its stopping behavior. By managing motor voltage during starting, it can limit starting current and reduce abrupt mechanical loading on the drive train. Different applications, however, place different demands on the starter. A conveyor or pump with normal starting requirements is not equivalent to a heavily loaded crusher, centrifuge, or large fan.

Soft starter product ranges are commonly grouped by performance level. Basic models focus on functions such as voltage-ramp starting, while general-purpose and high-performance models offer a broader set of control, protection, and application functions. Depending on the model, these can include adjustable current limiting, torque control, pump-stop functions, braking, reversing duty, or condition monitoring. Those functions are not available on every starter, so selection should begin with a clear list of what the process requires.

Load categories and starting classes provide a useful first filter. Normal starting may suit applications such as pumps, conveyors, compressors, and small fans. Heavy or very heavy starting can require a higher-performance device and more careful sizing. Application labels alone are not enough: actual load inertia, starting time, and starts per hour matter. A fan’s mass inertia, for example, can influence whether its starting duty is considered normal or very heavy.

Industrial soft starter selection and sizing

Size the starter using the motor’s required rated operational current and the actual starting conditions. Published motor power ratings are guide values tied to stated assumptions; they are not a substitute for checking the application. A starter selected for basic, normal starting may not be appropriate when the load needs a longer start, a higher starting current, or frequent starts.

Review the manufacturer’s limits for starting time, starting current, and starts per hour, along with the device’s current rating and operating temperature. If duty is heavier than the stated basis, a larger starter may be required. The motor and starter may also need additional sizing margin. For long starting times, motor temperature protection using a PTC sensor or temperature switch is recommended in the source guidance. Additional current loading during certain controlled ramp-down modes is another reason to account for motor thermal conditions.

A selection or simulation tool can help assess the combined motor and load data. The Siemens Simulation Tool for Soft Starters, for example, is described as using motor and load inputs to simulate an application and suggest suitable starters, including for heavy starting. Such tools support engineering decisions; they do not remove the need to confirm the real installation conditions and device limits.

Choose the circuit configuration deliberately

Three-phase soft starters may be connected in an inline or inside-delta circuit. The choice affects wiring, starter current, and installation compatibility.

  • Inline circuit: The starter is connected in series with the motor supply, using three leads to the motor. This is the simpler arrangement and can be preferable when the motor connections are long. The starter’s rated current corresponds to the motor’s rated current.
  • Inside-delta circuit: The starter phases are connected in series with the individual motor windings, with wiring similar to a wye-delta arrangement. It requires six motor leads, but the starter carries about 58% of the motor’s rated line current. This can allow a smaller starter for the same motor rating, provided the motor and installation support the arrangement.

Inside-delta wiring is not universally available. The source guidance notes that braking functions are possible only in an inline circuit and that inside-delta operation cannot be used on a 690 V line supply. Check the selected starter’s voltage and connection limits before designing the panel or specifying field cabling.

Check protection, supply, and installation conditions

Starter selection is only one part of motor feeder design. Fuses and switching devices are generally selected separately, and the main-circuit components should be dimensioned for the motor’s direct-on-line starting and the relevant short-circuit conditions. The harmonic content of starting current should also be considered when selecting motor starter protectors. Follow the device manufacturer’s requirements for coordination and protection.

Account for operating voltage, ambient temperature, installation altitude, and the supply system. Permissible voltage or current can be affected by these conditions, including derating at elevated temperatures or altitudes. The incoming transformer must also be capable of maintaining an acceptable voltage dip during motor starting. Where the transformer has little capacity margin, a separately supplied control voltage may help prevent a supply dip from switching off the starter.

Do not install capacitive equipment, such as power-factor correction equipment, between the soft starter and motor. Static or dynamic power-factor correction systems should not operate in parallel with the starter during starting or ramp-down, because this can cause problems for the compensation equipment or starter.

Plan commissioning around the application

Commissioning should verify that the selected settings fit both the motor and the driven process. Starting voltage, ramp-up time, current limits, and stopping behavior should be chosen for the required duty and checked against the starter’s capabilities. Higher-performance starters may provide application-specific functions, displays, communication options, or automatic parameterization, but these features vary by model. Communication and integration requirements should therefore be confirmed during specification, rather than assumed across a product family.

Conclusion

Reliable soft starter selection depends on aligning the device with motor current, load severity, starting frequency, desired stopping behavior, circuit configuration, and site conditions. Treat published motor ratings as starting points, verify all operating limits, and include feeder protection and supply-voltage effects in the design. This application-led process gives engineers and plant teams a sound basis for specifying, installing, and commissioning a motor starter.

Access Official Technical PDF

About The Author