Access Official Technical PDF

Share Summary:LinkedInEmail

Integrated p-GaN gate capacitors are a potential building block for compact, high-frequency power electronics. Joint work by the Hong Kong University of Science and Technology and Taiwan Semiconductor Manufacturing Company examined capacitors formed within p-type gallium nitride (p-GaN) gate structures on silicon. The approach could support integration of power switches with the passive components used by their gate-drive and control circuits.

For industrial automation engineers and power-system designers, the motivation is practical: parasitic inductance in a gate-drive loop can cause over-voltage stress as switching frequency rises. Integrating capacitors alongside the transistor may help reduce the need for external connections and support more tightly integrated power devices. The reported results also highlight important constraints, including gate leakage and recommended operating voltage.

Why integrate capacitors with p-GaN transistors?

Enhancement-mode GaN transistors are normally off: with zero gate potential, the device is in its current-off state. This behavior can reduce power consumption and enable fail-safe operation. GaN devices are also being developed for high-frequency power applications, where the aims include high conversion efficiency and power density. Fabrication on silicon is intended to reduce manufacturing cost.

At high frequencies, parasitic inductance in the gate-drive loop can produce voltage stress on the transistor. One way to minimize this inductance is to integrate the high-voltage power switch and its peripheral drive and control modules on the same chip. Integrated passive devices, including resistors and capacitors, can help make that system-level integration possible.

In a gate driver, capacitors can serve several purposes: decoupling power-supply noise, shifting voltage levels and pumping charge. Incorporating these functions near the transistor may help address the interconnection challenges associated with a separate gate-drive circuit. The study focused on whether p-GaN gate structures could also provide useful capacitor behavior.

How the p-GaN gate capacitor works

The capacitor used a metal/p-GaN/AlGaN/GaN stack based on material associated with commercial 650 V enhancement-mode power devices. It had a Schottky contact on the p-GaN side and ohmic contacts on the n-side. The researchers modeled the structure as two back-to-back diodes: a metal/p-GaN Schottky junction and a p-GaN/AlGaN/GaN heterojunction.

The p-GaN layer bends the underlying band structure upward. This depletes the two-dimensional electron gas (2DEG) that would otherwise form near the AlGaN/GaN interface, placing the transistor structure in its off state. The capacitor’s voltage-dependent behavior follows from how these regions contribute to the total capacitance.

Above the threshold for 2DEG formation, the Schottky diode capacitance varies with voltage, while the heterojunction capacitance is treated as voltage-independent and depends on the AlGaN barrier thickness. Below threshold, the heterojunction contribution becomes negligible. The resulting total capacitance is low and arises mainly from fringe or edge regions.

Measured capacitance, leakage and voltage limits

A rectangular device measuring 42 µm by 100 µm achieved a capacitance density of up to approximately 230 nF/cm2. The equivalent oxide thickness (EOT) of the stack ranged from 16 nm to 20 nm, with the corresponding voltage varying from 4 V to 7 V. Room-temperature DC breakdown was approximately 12.5 V.

Gate leakage caused a charged capacitor to discharge from 6 V to 5 V in about 60 µs, and from 5 V to 4 V in about 500 µs. The researchers interpreted these results as indicating suitability for AC operation above 100 kHz, where each period is shorter than 10 µs. These observations describe the reported capacitor behavior; they should not be read as a universal operating specification for every p-GaN device or circuit.

Leakage also has a power cost. The calculated consumption was approximately 30 µW at a 6 V bias and 4 µW at 5 V. In the researchers’ assessment, this was negligible compared with the overall consumption of circuits such as a gate driver that includes the capacitors. However, gate leakage increased with temperature, making thermal conditions relevant to evaluation.

The team advised limiting operating voltage to less than 7 V to avoid long-term stress-induced degradation. That recommendation is particularly important when translating laboratory measurements into circuit design: breakdown voltage is not the same as a suitable continuous operating voltage.

Electrode layout affects frequency performance

The researchers also compared a large-area circular electrode with an interdigitated design. The circular electrode had a 250 µm radius. The interdigitated version used six fingers, each measuring 54 µm by 360 µm, and provided comparable capacitance.

The layout comparison addressed the distribution effect of series resistance in the 2DEG. This effect can limit operating frequency by slowing turn-on. At 5 MHz, the interdigitated capacitor had a quality factor of 145, compared with 3.0 for the circular device. The result points to electrode geometry as an important consideration alongside capacitance when assessing an integrated device for high-frequency use.

Implications for power-electronics design

For system integrators and technical decision-makers, the work illustrates both the opportunity and the design checks involved in integrating passive components into GaN power devices. On-chip capacitors could support closer integration of switches and drive/control circuitry, addressing a source of gate-loop inductance. Their practical use still depends on matching voltage, leakage, temperature and frequency behavior to the requirements of the intended circuit.

The reported p-GaN gate capacitors combined useful capacitance density with low calculated leakage power under the stated bias conditions. At the same time, the less-than-7 V operating guidance and the improvement in quality factor with an interdigitated layout show why electrical limits and geometry matter. Integrated p-GaN capacitors are therefore best viewed as a promising component-level approach whose value must be assessed within the complete gate-drive and power-conversion design.

Access Official Technical PDF

About The Author