Access Official Technical PDF

Share Summary:LinkedInEmail

Interface trap characterization is important when evaluating β-Ga2O3 field-effect transistors (FETs), where the quality of the boundary between the gate insulator and semiconductor channel can affect device behavior and reliability. A sub-bandgap ultraviolet (UV) photonic current–voltage method provides a way to distinguish donor-like and acceptor-like interface traps using measurements made in both dark and illuminated conditions.

The method is relevant to engineers and technical decision-makers assessing wide-bandgap power-device technologies. Rather than relying on a single measurement across the entire subthreshold range, it uses two gate-voltage regions and the change in subthreshold ideality factor under illumination to estimate the energy distributions of the two trap types separately.

Why interface traps matter in β-Ga2O3 FETs

β-Ga2O3 is being investigated for power electronics because of its wide bandgap and high breakdown electric field. In metal-oxide-semiconductor (MOS) devices, the gate insulator helps control the channel and suppress gate leakage. That makes the interface between the insulator and the active channel a key part of device characterization.

Interface traps can capture or release charge as operating conditions change. Their density and energy distribution can therefore influence how the channel responds to the gate. Characterizing these states across the bandgap is useful for understanding device behavior, but separating donor-like states from acceptor-like states presents a measurement challenge.

Conventional characterization options include capacitance–voltage, conductance, transient spectroscopy, and current–voltage methods. The approach described here instead uses sub-bandgap UV illumination alongside drain-current measurements. Its aim is to extract both donor-like and acceptor-like interface-trap distributions from the photoresponsive change in current.

How sub-bandgap UV photonic I–V characterization works

The method compares the FET’s subthreshold drain current as a function of gate-to-source voltage (VGS) in dark and illuminated states. The experiment uses UV photons with energy below the β-Ga2O3 bandgap. In the reported device measurements, the illumination was at 390 nm, corresponding to a photon energy of 3.6 eV, below the material’s stated bandgap of 4.8 eV.

In the subthreshold region, current depends on the gate voltage and an ideality factor, η, which is related to the electrostatic response of the device. That response includes contributions from depletion capacitance and interface traps. Under illumination, photoresponsive charges add another contribution. Comparing η in dark and UV conditions helps isolate the illumination-related response from the baseline response.

The difference between the illuminated and dark ideality factors is used to estimate the photoresponsive capacitance. The method then examines how that difference changes with gate voltage and relates the result to surface potential. This provides a route from the measured electrical response to the energy distribution of photoresponsive trap states.

Separating donor-like and acceptor-like trap responses

A central feature of the technique is dividing the subthreshold operation into two regions using the flatband voltage (VFB):

  • Depletion region: Between turn-on voltage (VON) and VFB, the photoresponsive carriers are treated as primarily associated with donor-like interface traps.
  • Accumulation region: Between VFB and threshold voltage (VT), the photoresponsive response is treated as primarily associated with acceptor-like interface traps.

The flatband voltage is identified using the gate-current measurement configuration described in the study. In that configuration, the source terminal is floating, and the gate-to-drain current response helps distinguish changes associated with generation and recombination processes. The separate voltage regions then provide the basis for calculating donor-like and acceptor-like trap contributions rather than applying one surface-potential mapping across the entire subthreshold range.

For each region, the measured gate-voltage dependence of the differential ideality-factor response is converted into a change in photoresponsive capacitance. The resulting capacitance change is used to estimate the corresponding trap density as a function of energy. The approach thus combines electrical measurements, UV illumination, and region-specific analysis; it does not directly count individual traps.

What the reported measurements show

The experimental devices were bottom-gate β-Ga2O3 FETs with a thin, Sn-doped β-Ga2O3 nanomembrane transferred onto a SiO2 gate oxide. The measurements compared drain-current characteristics in dark and illuminated conditions and also used gate-current data to help identify the flatband voltage.

Using the proposed analysis, the researchers reported separate energy distributions for donor-like and acceptor-like interface traps. The extracted density ranges were 0.5 × 1011 to 5.5 × 1011 eV−1cm−2 for donor-like states and 2.1 × 1011 to 1.1 × 1012 eV−1cm−2 for acceptor-like states. These values describe the devices and method reported; they should not be treated as universal values for β-Ga2O3 interfaces.

Practical considerations and limitations

The method’s appeal is that it derives trap information from photonic I–V measurements and separates the two trap categories using different subthreshold regions. However, interpretation depends on device geometry and on distinguishing interface contributions from other photoresponsive effects.

In particular, illumination can also excite carriers associated with bulk traps in the β-Ga2O3 film. The study notes that this contribution may cause errors in the extracted interface-trap density, and that measurements across different channel thicknesses would be useful for assessing the influence of interface and bulk traps. The approach also has a geometry constraint: in top-gate devices, an opaque gate metal can prevent light from reaching the channel. Tilted illumination or back-side illumination through a transparent substrate are identified as possible ways to address that constraint.

These considerations matter when deciding whether the technique is appropriate for a device structure. Measurement setup, optical access, gate-current behavior, and the assumptions used to assign responses to each voltage region all affect how the results should be interpreted.

Conclusion

Sub-bandgap UV photonic I–V measurement offers a method for separately estimating donor-like and acceptor-like interface-trap distributions in β-Ga2O3 FETs. Its key analytical steps are comparing dark and illuminated subthreshold ideality factors, using the flatband voltage to define two operating regions, and mapping the resulting response to surface potential and trap energy.

For device-development teams, the practical implication is a characterization option that can complement other electrical techniques, particularly when distinguishing trap types is important. Results should be evaluated with attention to bulk-trap contributions and optical access to the channel; those factors shape both the applicability of the method and the confidence of the extracted interface data.

Access Official Technical PDF

About The Author