Access Official Technical PDF

Share Summary:LinkedInEmail

Reducing size, weight and power (SWaP) is a central challenge when designing radar for platforms with limited space and payload capacity. A Ka-band radar can help address these constraints: higher operating frequencies enable smaller microwave components, while advanced packaging can bring multiple functions together in a compact assembly. One demonstrated stepped-frequency continuous-wave (SFCW) design combined these approaches using a low-temperature co-fired ceramic (LTCC) multi-chip module (MCM).

The result was a substantial reduction in footprint, power consumption and weight compared with an earlier connectorized implementation. Just as importantly, a direct loop-back test showed that the integrated design produced an intermediate-frequency output comparable to its predecessor. The work illustrates how system integration can support compact radar design without relying solely on smaller individual components.

Why integrate a Ka-band radar?

The radar was developed with unmanned aerial vehicle applications in mind, where available space and payload capacity can constrain system design. The SFCW system transmits across 30–36 GHz in 20 MHz increments. Operating at high frequencies reduces the electrical length of microwave structures, including antennas and other RF components, creating opportunities for more compact equipment.

A second strategy is to replace connectorized commercial off-the-shelf components with a more integrated architecture. The earlier radar used coaxial microwave components and evaluation boards. In the new design, bare die were wire-bonded to an LTCC substrate, while microwave filters and a Wilkinson power divider were incorporated into the module. A drop-in mixer was also included in the integrated RF front end.

These choices reduce the number of separate assemblies and interconnections. They also introduce a design challenge: placing transmit and receive functions close together can increase electromagnetic coupling. At Ka-band, packaging must therefore address not only physical size but also the interaction between circuits inside the module.

LTCC packaging and circuit integration

The MCM used an eight-layer LTCC stack-up made from 9K7 ceramic. Its overall thickness was selected to align with the mixer carrier board, helping keep wire bonds short. The substrate incorporated a Ka-band band-pass filter, a low-pass filter and a two-way Wilkinson power divider.

The band-pass filter was implemented as a substrate-integrated-waveguide evanescent combline structure. Integrating it into the LTCC stack-up eliminated the need for a separate connectorized filter; the design achieved a reported 30-fold size reduction for that filter compared with commercial coaxial modules. The low-pass filter was designed to attenuate local-oscillator and RF leakage signals at the mixer. The integrated power divider split the local-oscillator signal between the conversion mixers.

Signals entered and left the assembly through GPPO connectors mounted in a back-plate. The back-plate also provided structural support and a path for heat dissipation. On the LTCC, conductor-backed coplanar waveguide transmission lines connected the circuit elements. Via stitching was used to support transmission-line performance across the operating frequency range.

Managing electromagnetic coupling

In a compact RF assembly, transmit and receive circuits can be susceptible to unwanted coupling from nearby subsystems. The design addressed this by surrounding individual microwave circuits with metal seal-frame walls and adding a metal lid. Grooves in the lid aligned with the walls, allowing the lid to sit flush with the assembly.

This grounded barrier structure was intended to contain radiated fields and improve isolation between sensitive circuits. The approach highlights an important consideration for integrated radar: miniaturization can make packaging-level electromagnetic compatibility part of the circuit design, rather than a concern that can be handled only after the components are assembled.

Power distribution and system control

A separate power distribution board supplied 12 voltage outputs to the card-deck radar from +8 V and −5 V inputs. Seven outputs were fixed, while five could be adjusted for gate-voltage tuning using digital potentiometers. Each output could be enabled or disabled individually.

The board’s microcontroller processed commands received through a USB-UART bridge. Users could configure the outputs through a LabVIEW interface and select power-up and power-down sequences with time delays. A configuration could also be stored in onboard flash memory for recall when the board was next powered on. This arrangement provided controlled biasing for amplifiers and frequency doublers within the radar system.

Measured SWaP reduction and performance

The integrated card-deck radar measured 2 by 3 inches, giving it a footprint of 6 square inches. The original connectorized radar measured 25 by 15.5 inches, or 387.5 square inches. This represented a 64-fold reduction in footprint area. Power consumption decreased from 13.54 W to 6.74 W, approximately half the original level. Weight fell from 10.2 pounds to less than one pound, a reduction of more than tenfold.

To compare operation, both systems were tested in a direct loop-back configuration: the transmitter output was connected to the receiver input, and the intermediate-frequency output was measured with a spectrum analyzer before baseband down-conversion. The expected output was a 12.8 GHz tone at approximately −14.5 dBm. The connectorized system measured −14.89 dBm, while the integrated system measured −14.62 dBm. Both produced a spectrally pure tone near the expected power, supporting the conclusion that the integrated design performed comparably in this test.

This measurement was a loop-back verification, not a demonstration of in-flight performance. It provides evidence that the integrated RF front end maintained the measured signal behavior of the earlier system while reducing its physical and power requirements.

Practical implications for compact RF systems

For engineers developing radar or communication equipment for space-constrained platforms, the design offers several practical lessons:

  • Integrate at the subsystem level: Bare-die assembly and LTCC structures can consolidate microwave functions that would otherwise use separate connectorized components.
  • Design isolation into the package: Metal walls and a lid can help manage electromagnetic coupling in a dense layout.
  • Verify performance against a baseline: Comparing loop-back measurements provides a direct check that integration has not materially changed the tested output.
  • Consider power control alongside RF layout: Sequenced, configurable bias supplies are part of making an integrated radar assembly practical to operate.

The Ka-band radar example shows how LTCC integration, careful RF packaging and dedicated power distribution can work together to reduce system footprint, power consumption and weight. For technical decision-makers, the key takeaway is that miniaturization depends on more than shrinking components: it requires coordinated design of the microwave circuits, isolation structures, interconnects and power architecture. A measured comparison with the original system can then help establish whether those packaging changes preserve the required functionality.

Access Official Technical PDF

About The Author