Access Official Technical PDF

Share Summary:LinkedInEmail

Reliable communications can be difficult to provide in places beyond the reach of conventional networks, including sparsely populated rural areas and the open sea. Satellite links offer a way to connect these locations, but they depend on capable equipment at both ends of the link. A Ka-band satellite transceiver developed by researchers at Tokyo Institute of Technology and Socionext explores how standard CMOS technology could support compact, lower-complexity satellite communications equipment for ground platforms.

The prototype is designed to communicate with satellites in low Earth orbit (LEO), medium Earth orbit (MEO) and geostationary Earth orbit (GEO). Its architecture combines a high-linearity transmitter, a dual-channel receiver and direct conversion of signals. Together, these features address important design considerations for satellite communications (SATCOM): efficient transmission, reception in the presence of interference, and implementation in an integrated chip.

Ka-band satellite transceiver design for ground platforms

For SATCOM, the Ka band described in the research covers 27–31 GHz for uplink signals travelling from the ground to a satellite, and 17–21 GHz for downlink signals travelling from a satellite to the ground. Operating at these frequencies makes the transceiver relevant to satellite broadband applications, where equipment must handle high-frequency signals in a compact implementation.

The research team built its design using standard complementary metal-oxide-semiconductor (CMOS) technology. CMOS is widely used to manufacture highly integrated circuits. Using it for a Ka-band transceiver offers a route to implementing the required radio-frequency functions in silicon rather than relying exclusively on less integrated approaches. The prototype chip measures 3 mm by 3 mm; that dimension describes the chip itself, not a complete satellite communications terminal.

Transmitter design emphasizes efficiency and linearity

On the transmit side, the design uses a high-quality-factor transformer. According to the researchers, this helps improve power efficiency and transmission linearity. Linearity matters because distortion can alter a transmitted signal, so maintaining it is an important part of supporting the intended modulation schemes.

The prototype was evaluated with modulation schemes regulated by the DVB-S2X satellite communications standard. These include high-order amplitude and phase shift keying (APSK) formats such as 64 APSK and 256 APSK. Higher-order modulation encodes information using combinations of carrier amplitude and phase, enabling fast data rates when conditions and system design support its use. The source reports promising test results but does not provide numerical performance figures in the press release.

Dual-channel reception and interference cancellation

The receiver uses two channels, enabling it to receive signals from two satellites simultaneously. The channels can operate with two independent polarization modes or at two different frequencies. This parallel reception capability gives the architecture flexibility in how signals are handled.

A further feature is adjacent-channel interference cancellation. In a receiver, a strong signal in a nearby frequency band can interfere with the signal of interest. The proposed design uses information received through the other channel to help cancel this adjacent-channel interference. The stated benefit is an increase in dynamic range, allowing the receiver to operate correctly in conditions with stronger noise and interference than it could otherwise tolerate. The release does not quantify that improvement.

Direct conversion reduces conversion stages

Both the transmitter and receiver use direct conversion. On transmit, the circuit converts a baseband signal—the original information signal before it is placed on a radio-frequency carrier—directly into a modulated signal. On receive, the process is reversed, converting the received signal back to baseband.

This differs from a superheterodyne receiver, which uses an intermediate frequency stage between the incoming radio signal and the baseband signal. Avoiding additional intermediate-frequency conversions can reduce overall circuit complexity, size and power consumption, as described by the researchers. The release does not give figures for the resulting savings, so the practical comparison depends on the complete equipment and implementation.

Why the architecture matters for remote connectivity

For system designers and technical decision-makers, the work is an example of integrating several SATCOM radio functions within a CMOS implementation. The combination of direct conversion, dual-channel reception and interference cancellation is relevant to designing ground-platform equipment that must communicate across different satellite links and cope with less-than-ideal signal conditions.

Potential applications include connectivity for remote rural locations and maritime settings, where satellite communications can provide links beyond the reach of terrestrial infrastructure. The transceiver is a research prototype, not evidence that a complete commercial terminal or service is available. Its significance is in demonstrating an approach to Ka-band SATCOM circuitry that the researchers designed for communication with satellites in multiple orbital regimes.

The work, presented at the 2020 IEEE Radio Frequency Integrated Circuits Symposium, was developed by researchers from Tokyo Tech and Socionext. The team described it as the first Ka-band SATCOM transceiver implemented using standard CMOS technology and designed for ground-platform communication with both GEO and LEO satellites. GEO satellites orbit at approximately 35,786 km, while LEO satellites occupy the 200–2,000 km range stated in the release.

Practical implications for SATCOM development

Satellite connectivity depends not only on the spacecraft, but also on the radio hardware that transmits and receives signals on the ground. This prototype brings together a linear transmitter, a flexible two-channel receiver and a direct-conversion architecture on a small CMOS chip. Its reported testing across DVB-S2X modulation schemes makes the design relevant to ongoing efforts to develop integrated Ka-band satellite communications equipment.

For industrial automation and operations teams considering satellite links for remote assets, the research is a technology development rather than a ready-to-deploy solution. Still, it illustrates how integrated transceiver design may help address equipment size, complexity and interference challenges as SATCOM systems evolve. Those capabilities could support broader connectivity options for operations in locations where terrestrial communications are difficult to provide.

Access Official Technical PDF

About The Author