Access Official Technical PDF

Share Summary:LinkedInEmail

In high-output-current power supplies, the output filter must control both steady-state ripple and voltage changes when the load shifts quickly. An all-ceramic solution can meet demanding transient requirements, but the necessary bulk capacitance may increase component cost and consume substantial PCB area. Mixed capacitor filtering—using ceramic capacitors alongside aluminum-polymer or solid aluminum electrolytic capacitors—offers another approach for buck-converter designs.

The design challenge is to allocate the filtering work appropriately. Ceramic capacitance supports ripple and noise filtering, while bulk capacitance helps limit output-voltage excursions during load transients. The right combination depends on the converter, output current, load-step requirements and acceptable transient voltage response.

Why use mixed capacitor filtering?

The NCV881930 and NCV891930 are synchronous buck controllers with preset internal slope and feedback-loop compensation. Their compensation is designed around defined current-sense resistor and output-filter component values, including relatively large output capacitance for applications with substantial load transients. The two controllers operate at different switching frequencies: 410 kHz for the NCV881930 and 2 MHz for the NCV891930.

For these designs, an all-ceramic output filter may require a large number of capacitors. The application guidance identifies a mixed ceramic and aluminum-polymer approach as a way to reduce cost and PCB area. That is not a reason to substitute components without analysis: the capacitor mix must still meet the power supply’s ripple, noise and transient-response requirements.

Separate steady-state ripple from transient needs

Capacitor selection involves two related but distinct design checks. First, determine the minimum ceramic capacitance needed for steady-state ripple and noise filtering. The application note relates this value to switching frequency, output inductance and the specified ripple voltage. In practical terms, the filter must be evaluated in the context of the converter’s operating conditions, rather than by choosing capacitance from output current alone.

Second, determine the bulk capacitance needed to support a load step. When load current rises, the output capacitors supply current while the regulator responds. The resulting voltage deviation depends on the size of the current step, the allowed voltage transient, the power-supply bandwidth, the bulk capacitor’s effective capacitance and its equivalent series resistance (ESR).

ESR matters because it contributes to the immediate voltage change associated with a load step. For the same current change, a bulk capacitor with higher ESR produces a larger output-voltage transient. Consequently, nominal capacitance by itself is not enough to assess whether a proposed bank will meet the response requirement.

What the recommendations show

The mixed-capacitor recommendations in the application note are based on a load step from 50% to 100% of rated current and a maximum voltage transient response of ±3%. These conditions describe the basis for the listed combinations; they should not be treated as universal values for other load profiles or voltage limits.

For the 410 kHz NCV881930, the examples use two 22 µF ceramic capacitors across several output-current ratings, with aluminum-polymer bulk capacitance increasing as current rises. At 5 V, the listed combinations range from two 100 µF aluminum-polymer capacitors at 6 A to three 220 µF capacitors at 20 A. The 3.3 V recommendations include examples at 6, 8 and 10 A, with two 120 µF, two 180 µF and two 220 µF aluminum-polymer capacitors, respectively, alongside two 22 µF ceramics.

For the 2 MHz NCV891930, the recommended banks are smaller in the examples shown. At 5 V and 2 A, the combination is one 10 µF ceramic and one 56 µF aluminum-polymer capacitor. At 5 V and 8 A, it is two 10 µF ceramics and two 100 µF aluminum-polymer capacitors. These are controller-specific recommendations, not interchangeable designs: the appropriate configuration depends on the selected controller, output voltage and current rating.

Account for derating and capacitor characteristics

Nominal capacitance does not necessarily equal effective capacitance in the circuit. The application guidance notes that ceramic capacitor derating should be considered using the controller datasheet’s application information. Its analysis includes an initial 20% derating for aluminum-polymer capacitance, while also cautioning that additional derating may be necessary.

ESR also varies among the capacitor types and values listed. For example, the cited 10 µF and 22 µF ceramic components have ESR values of 2.9 mΩ and 4.0 mΩ, respectively. The listed aluminum-polymer parts range from 28 mΩ for 33–68 µF devices to 15 mΩ for 120–220 µF devices. Designers considering different components should evaluate their actual capacitance and ESR against the transient-response requirements rather than assuming that a similar nominal value will behave identically.

The output filter may also need additional low-value ceramic decoupling for high-frequency noise. The guidance gives 0.1 µF and 1 nF as example values. These capacitors complement the main output bank; they do not replace the bulk-capacitance analysis.

Apply the method to the actual power supply

For an engineering review or design iteration, a practical sequence is:

  • Define the operating requirements: specify output current, load-step amplitude and permitted voltage deviation.
  • Check steady-state filtering: determine the ceramic capacitance needed for ripple and noise performance.
  • Size the bulk bank: account for load-step current, converter bandwidth and capacitor ESR.
  • Include derating: assess effective ceramic and aluminum-polymer capacitance in the intended application.
  • Validate the complete design: confirm operating parameters and transient response with the selected components and circuit.

The component tables provide a useful starting point for the specified NCV881930 and NCV891930 conditions, but the power supply’s technical requirements remain decisive. A capacitor bank that matches a table entry may still need review if the load profile, voltage tolerance or selected components differ.

Conclusion

Mixed capacitor filtering can provide a practical alternative to an all-ceramic output bank when bulk capacitance would otherwise raise cost or occupy too much PCB area. The key is to treat ripple filtering and load-transient support as separate design checks, then account for ESR and capacitance derating in the combined solution. Use controller-specific recommendations as a reference, and validate the final output filter against the actual application’s load steps and voltage limits.

Access Official Technical PDF

About The Author