Sub-THz waveguide transmission is relevant not only to signal delivery, but also to how much information a channel can carry. Measurements from 160 to 300 GHz show that the transmission of a single-mode rectangular waveguide can vary substantially with frequency when its source and detector are poorly impedance-matched to the guided mode. That variation also affects the estimated information rate, an important consideration when evaluating waveguides for high-frequency and quantum communication systems.
Why waveguide transmission matters for information capacity
A waveguide confines electromagnetic energy and can reduce radiative losses compared with sending a signal through free space. In communication engineering, however, low loss is only part of the picture. Channel capacity describes the maximum rate at which information can be conveyed reliably, expressed in bits per second or, in some analyses, bits per photon.
The study examined a rectangular waveguide carrying the fundamental TE10 mode. In this mode, the electric field has a defined linear polarization within the guide. The researchers measured transmission over a broad sub-terahertz range and related the frequency-dependent response to channel-capacity calculations. The central finding is that transmission through the assembly is shaped not just by propagation along the guide, but also by how the source, antennas and waveguide are electrically connected.
How impedance mismatch shapes sub-THz waveguide transmission
The experimental source and detector had characteristic wave impedances estimated at about 140 kΩ, while the fundamental waveguide mode had an impedance roughly two orders of magnitude lower. This large mismatch causes reflections at the interfaces. As a result, waves can interfere within the antenna-and-waveguide assembly, producing a transmission response that changes with frequency rather than a smooth, uniform passband.
The experiment used photo-mixers to generate and detect tunable signals, diagonal-horn antennas to couple signals into and out of the guide, and copper-tellurium waveguides of two lengths. The team measured signal amplitude with high dynamic range and frequency resolution. The longer guide showed more pronounced variation across the band than the shorter guides, while both lengths displayed a transmission onset near the expected single-mode operating region.
Modeling combined the antenna and waveguide responses using an ABCD-matrix approach. Agreement between model and measurements required accounting for small differences between nominal and realized waveguide dimensions. This sensitivity is consistent with a system that is many wavelengths long and has a substantial impedance mismatch: small dimensional or assembly changes can shift standing-wave patterns and alter the measured amplitude.
From measured transmission to channel capacity
Transmission determines how much of the launched signal reaches the receiving end. In a practical lossy channel, that delivered power influences the signal-to-noise conditions and therefore the achievable information rate. For the measured system, the estimated wideband coherent-state channel capacity varied across the transmission band. The study reports an information rate of about one bit per photon under the conditions considered.
This estimate is not a universal capacity for rectangular waveguides. It depends on the transmitted power, frequency-dependent transmission, channel type and waveguide geometry. The fundamental mode’s group velocity also changes near cutoff. As frequency approaches the cutoff from above, propagation slows, and the theoretical capacity contribution associated with that mode falls.
Quantum communication introduces additional constraints. For a coherent-state channel, quantum noise affects the capacity estimate; a number-state channel has a different theoretical limit. The paper discusses both cases and notes that realizing their maximum rates requires suitable photon-occupation distributions across frequency channels. The measured system’s result is therefore best understood as an estimate for a particular configuration, not as a direct demonstration of a complete quantum communication link.
Implications for quantum and high-frequency system design
The findings point to several practical considerations for engineers and technical decision-makers assessing sub-THz links:
- Include interfaces in the channel model. Antennas, source and detector impedances, and the waveguide should be analyzed as one connected system rather than as independent components.
- Account for frequency-selective behavior. A usable band may contain peaks and dips in transmission that affect power delivery and information capacity.
- Control dimensions and assembly. Small changes in cross-section or mounting can influence the standing-wave response, particularly when the overall path is long relative to wavelength.
- Distinguish capacity models. Coherent-state and number-state channels have different theoretical treatments, so estimates should match the intended signaling approach.
The work also identifies a possible direction for quantum networks: coupling a Josephson-junction single-photon source to a superconducting waveguide could support an on-demand, narrow-bandwidth free-space number-state channel. This is presented as a proposed application of the analysis, rather than as a capability demonstrated by the reported waveguide measurements.
Conclusion
Sub-THz waveguide performance depends on more than conductor loss and nominal cutoff frequency. In the measured setup, a large impedance mismatch between photo-mixers and the TE10 waveguide mode produced a strongly frequency-dependent transmission response, which carried through to the estimated channel capacity. For system designers, the practical lesson is to model coupling, geometry, propagation and signal type together. That integrated view is essential when evaluating high-frequency waveguides for information transfer or future quantum communication architectures.