Access Official Technical PDF

Share Summary:LinkedInEmail

Thermochromic solar collectors are designed to respond to temperature rather than relying on fixed optical properties. A coating based on vanadium dioxide (VO₂) can change its behavior as it heats up, increasing thermal emittance above a transition temperature. This offers a passive way to limit overheating in a flat plate collector. Modeling of a proposed absorber shows the potential trade-off: stronger heat rejection can reduce stagnation temperature, while changes in solar absorptance can affect both normal operation and overheating protection.

How a thermochromic absorber works

A conventional selective absorber aims to capture incoming sunlight while limiting heat loss through infrared radiation. These properties are commonly described as solar absorptance and thermal emittance. High solar absorptance helps the collector take in solar energy; low thermal emittance reduces radiative heat loss from the absorber.

A thermochromic coating changes its optical response with temperature. VO₂ undergoes a reversible semiconductor-to-metal phase transition at about 68°C, though the transition temperature can be adjusted through doping. The change is especially marked in the near- and mid-infrared parts of the spectrum. In a solar thermal collector, the intended effect is to retain low thermal emittance at ordinary operating temperatures and increase it when the absorber becomes hot.

The proposed multilayer absorber combined an infrared-reflective aluminum substrate with a VO₂ film, a black spinel selective absorber layer, and a silica-based antireflective top layer. The aluminum supports infrared reflection, while the other layers shape the coating’s response to incoming sunlight and emitted heat.

Thermochromic solar collectors: measured optical changes

The absorber’s spectral reflectance was measured at room temperature and at 100°C. From these measurements, the researchers determined solar absorptance and thermal emittance for each temperature state. The measured solar absorptance rose from 0.84 at room temperature to 0.91 at 100°C. Thermal emittance increased more substantially, from 0.09 to 0.40.

That increase in emittance is central to the overheating-control concept: a hotter absorber can radiate more energy away. But the simultaneous rise in solar absorptance works against that effect by allowing the absorber to take in more solar energy. The balance between the two properties—not the phase transition alone—determines the collector’s thermal behavior.

The measured high-temperature emittance was also higher than the value predicted by the optical simulation. The study suggests that differences in the deposited VO₂ film, including possible impurities arising from the challenges of controlling oxygen during deposition, could help explain the discrepancy. This highlights why measured coating properties matter when predicting collector performance.

What the collector simulations indicate

A numerical model was used to estimate the thermal efficiency curves and stagnation temperatures of a single-glazed flat plate collector. The model considered steady-state operation, heat transfer through solids and fluids, temperature-dependent material properties, and discretization across the collector. The measured optical properties of the thermochromic absorber were compared with a standard selective absorber having solar absorptance of 0.95 and thermal emittance of 0.05.

For the measured thermochromic absorber, designated A1, the calculated stagnation temperature was 152°C, compared with 177°C for the standard collector. Stagnation temperature is the temperature a collector can reach when heat is not being removed for useful operation. The modeled 25°C reduction for A1 was attributed mainly to its increase in thermal emittance across the phase transition. Its lower solar absorptance than the standard absorber also contributed, although the increase in absorptance at high temperature partly limited the benefit.

The efficiency curve for A1 showed a small, sudden drop around the thermochromic transition, in addition to the general decrease in efficiency as inlet fluid temperature increased. At ordinary operating temperatures, A1’s lower solar absorptance means its modeled efficiency was below that of the standard absorber.

Why absorptance must be considered alongside emittance

Two additional absorber cases explored how changing solar absorptance could affect performance. These were modeled scenarios, not measured collector coatings. Both retained the temperature-dependent emittance measured for A1, but assumed solar absorptance stayed constant through the transition:

  • A2: Solar absorptance remained at 0.84, the measured room-temperature value. Its modeled stagnation temperature was 147°C.
  • A3: Solar absorptance was set to 0.95, matching the standard absorber’s value. Its modeled stagnation temperature was 155°C.

A2’s lower absorptance resulted in a lower predicted stagnation temperature, but also implies less solar energy absorbed during normal operation. A3 was modeled to perform more like the standard collector under normal operating conditions, while its increased high-temperature emittance still produced a sharp efficiency decrease at the transition. The simulations therefore point to a design objective: maintain high solar absorptance at lower temperatures, then reduce absorptance while increasing thermal emittance at elevated temperatures.

Practical implications for collector design

For engineers and system designers, the results show why a thermochromic absorber should be evaluated across its full operating-temperature range. A strong increase in thermal emittance can help lower stagnation temperature, but performance depends on the absorber’s solar absorptance before and after transition as well. A coating that rejects heat effectively at high temperatures may still compromise useful heat collection if its low-temperature absorptance is too modest.

The reported temperatures come from simulations using measured properties for A1 and assumed properties for A2 and A3. They are useful for comparing design directions, but the projected cases should not be treated as demonstrated hardware performance. Further absorber development would need to improve low-temperature absorptance while avoiding an increase in absorptance at high temperature.

Conclusion

VO₂-based thermochromic solar collectors offer a passive approach to overheating control by increasing thermal emittance as the absorber heats. In the modeled flat plate collector, the measured absorber reduced stagnation temperature by 25°C relative to a standard collector, but its changing and comparatively modest solar absorptance limited efficiency. The most promising design direction combines strong solar absorption during normal operation with higher emittance—and ideally lower absorptance—above the transition. For practical evaluation, both optical properties and their temperature dependence must be considered together.

Access Official Technical PDF

About The Author