Access Official Technical PDF

Share Summary:LinkedInEmail

Ultraviolet sensing can provide a way to detect radiation in applications ranging from environmental monitoring to optical and other sensing systems. One approach is a ZnO UV photodetector, which uses zinc oxide as its light-sensitive semiconductor. A comparative study of undoped ZnO, aluminum-doped ZnO (AZO), and gallium-doped ZnO (GZO) thin films examined how these material choices affect optical, electrical, and UVA photoresponse properties.

The devices used a metal-semiconductor-metal (MSM) configuration with interdigitated aluminum electrodes. Under the reported test conditions, the GZO-based detector produced the highest UV response ratio and photocurrent responsivity. The results illustrate why thin-film composition and device design should be assessed together when evaluating a photodetector for a sensing system.

Why use ZnO for ultraviolet detection?

Zinc oxide is a wide-bandgap semiconductor that absorbs ultraviolet light while remaining highly transparent across much of the visible range. That combination makes it a candidate sensing layer for UV detectors. The study reports an optical bandgap of about 3.29 eV for the prepared films, slightly below the stated bulk ZnO value of 3.37 eV.

MSM photodetectors are built around a semiconductor layer contacted by two metal electrodes. In this design, interdigitated electrodes create repeated contact fingers across the sensing film. The study describes MSM structures as relatively simple to fabricate and suitable for integration, while their operation in photoconductive mode allows illumination-driven changes in current to be measured.

Comparing ZnO, AZO, and GZO thin films

The three films were deposited on glass using sol-gel spin coating. Aluminum and gallium were each added at a concentration of 1 atomic percent in their respective precursor solutions. X-ray diffraction indicated that all three films were polycrystalline ZnO with a hexagonal wurtzite structure. The analysis also indicated that the dopants entered the ZnO lattice without forming a detectable second phase.

Doping affected both the film structure and its measured properties. Compared with undoped ZnO, the doped films had smaller average crystallite sizes and lower surface roughness. AZO had the smallest average crystallite size, at 16.2 nm, while GZO measured 22.5 nm and ZnO 26.1 nm. The average surface roughness values were 2.86 nm for AZO, 3.08 nm for GZO, and 5.13 nm for ZnO.

Both doped films also showed higher average visible-range transmittance than undoped ZnO. Across 400–800 nm, the reported averages were 88.6% for ZnO, 91.6% for AZO, and 91.4% for GZO. The study associated the improvement with smoother surfaces and reduced film thickness. For applications where transmission through the sensing layer matters, these measurements offer a useful comparison between the three compositions.

Electrical measurements showed a clearer distinction between AZO and GZO. Both dopants increased electron concentration and mobility relative to undoped ZnO, but GZO had the highest reported mobility and lowest resistivity. The respective resistivities were 7.71 × 103 Ω·cm for ZnO, 4.14 × 102 Ω·cm for AZO, and 1.22 × 102 Ω·cm for GZO. These measurements indicate that the effect of doping depends on the dopant selected, even when the nominal concentration is the same.

UVA response of the MSM photodetectors

Each detector was tested at room temperature under UVA illumination from a mercury lamp, with a reported power density of approximately 0.825 mW/cm2. The devices were measured at a 5 V bias. Their current-voltage characteristics were linear in both dark and illuminated conditions, consistent with ohmic contact behavior between the aluminum electrodes and the semiconductor films.

Illumination caused a sharp increase in current for all three devices. The measured photocurrents were 0.14 mA for ZnO, 1.11 mA for AZO, and 2.38 mA for GZO. Doped films also had higher dark current than undoped ZnO, reflecting their higher electron concentrations. For this reason, photocurrent alone does not provide a complete comparison: the study also assessed the ratio of illuminated current to dark current.

  • ZnO: UV response ratio of 15.3 and photocurrent responsivity of 12.0 A/W.
  • AZO: UV response ratio of 35.5 and photocurrent responsivity of 28.0 A/W.
  • GZO: UV response ratio of 73.3 and photocurrent responsivity of 46.2 A/W.

Under these specific test conditions, GZO led on both measures. Its response ratio compares the UVA photocurrent with the dark current, while responsivity expresses photocurrent relative to incident optical power. These are distinct indicators, so engineers should consider both alongside operating conditions and the requirements of the intended detection task.

Interpreting switching behavior and design trade-offs

When UVA illumination was switched on, current rose and approached a saturation level. Switching the light off reduced the current, but it did not immediately return to its initial value. The study attributes this persistent photoconductivity behavior to charge trapping and release processes associated with the semiconductor and its surface. It also reports slower current decay during recovery for the AZO and GZO devices.

The comparison highlights a practical trade-off: doping improved measured transparency and electrical conductivity, but also increased dark current. A higher photocurrent therefore does not automatically mean a higher response ratio or greater suitability for every application. Material selection should account for the desired balance of optical transmission, baseline current, illuminated response, and recovery behavior.

Practical implications

For the sol-gel-derived films and MSM devices evaluated, Ga doping produced the strongest overall UVA photoresponse, with a UV response ratio of 73.3 and responsivity of 46.2 A/W at 5 V. Al doping also improved several properties compared with undoped ZnO, including visible-range transmittance and measured electrical performance, but its detector response was lower than GZO’s in this comparison.

These findings provide a basis for choosing between ZnO-based sensing layers, not a universal performance guarantee. Actual device evaluation should use relevant illumination, bias, and operating conditions. For engineers and system integrators assessing UV detection, the central lesson is to compare the complete photoresponse profile—including dark current and recovery behavior—rather than relying on photocurrent alone.

Access Official Technical PDF

About The Author