Access Official Technical PDF

Share Summary:LinkedInEmail

A silicon nitride integrated laser could help address a long-standing gap in photonic integrated circuits: Si3N4 platforms offer low-loss passive waveguides and optical components, but adding an efficient on-chip light source is challenging. A demonstrated III-V/Si/Si3N4 architecture tackles that problem by combining semiconductor optical gain with a silicon nitride laser cavity. The result illustrates how multilayer heterogeneous integration can bring distinct material properties together in a single device.

Why combine III-V, silicon and silicon nitride?

Each layer has a different role. An indium phosphide (InP) multiple-quantum-well section supplies optical gain when electrically driven. Silicon provides an intermediate waveguide layer, while Si3N4 forms the passive cavity elements. This arrangement avoids relying on a direct transition between a relatively thick III-V gain layer and a Si3N4 waveguide, whose refractive indices differ substantially.

That transition is a practical integration challenge: inefficient optical coupling can add loss, while reflections can interfere with laser operation. Separately aligning and packaging a III-V gain chip with a Si3N4 external cavity—the butt-coupled approach—also requires optical alignment between chips. The multilayer design instead integrates the layers and guides light between them through a sequence of waveguide transitions.

How the silicon nitride integrated laser is structured

The device uses a 1.5 mm-long InP/Si hybrid section for gain. At either end of the cavity, a narrow-band Si3N4 spiral distributed Bragg reflector (DBR) and a broadband tunable silicon loop mirror provide the laser mirrors. A thermo-optic tuner between the gain section and the Si-to-Si3N4 transition adjusts the optical phase inside the cavity.

The spiral DBR packs a 20 mm grating path into a footprint of 3.5 mm by 3.6 mm. Its 526 nm grating period produces a reflection peak near 1550 nm. Circular Si3N4 posts along the curved waveguide form the grating. A separate spiral waveguide acts as a low-reflection terminator for light passing through the grating.

Light moves from the InP/Si gain section through a silicon waveguide and then into Si3N4. At the silicon-to-Si3N4 interface, a dual-level silicon taper gradually changes the waveguide mode over 200 micrometres. The transition passes through a hybrid Si/Si3N4 mode, providing a route between the fundamental transverse-electric modes of the two waveguides.

Measured laser performance

At a stage temperature of 20°C, the laser had a continuous-wave lasing threshold of 75 mA. Its peak on-chip output power exceeded 0.5 mW at a gain current of 320 mA, and its differential resistance was about 2.5 ohms. The Si3N4 spiral grating provided more than 20 dB sidelobe extinction, and the measured side-mode suppression ratio exceeded 58 dB in a stable single-mode state.

The laser also showed mode hopping as gain current increased. Changes in gain-section temperature and the different thermal responses of the longitudinal modes and DBR reflection peak can shift the selected longitudinal mode. In this device, the wavelength step associated with mode hopping was about 0.025 nm. The measurements also showed that optical phase affects mode behavior and power, making phase tuning an important part of operating and characterizing the cavity.

Temperature stability and frequency noise

Silicon nitride and silicon dioxide have lower thermo-optic coefficients than silicon and InP at 1550 nm. Because the DBR cavity is based on Si3N4, its wavelength is less affected by temperature changes than a cavity based on silicon or InP. Across a stage-temperature change from 10°C to 55°C, the III-V/Si/Si3N4 laser shifted by 0.47 nm, or 10.46 pm/°C. An InP/Si DBR comparison laser shifted by 3.3 nm, or 73.18 pm/°C, over the same temperature range.

Frequency-noise measurements showed a white-noise-limited level of about 2,000 Hz²/Hz, corresponding to a 6 kHz Lorentzian linewidth with the silicon loop mirror at its untuned reflectivity. Tuning the mirror to maximum reflectivity increased photon density in the cavity; the measured noise level then fell to about 1,300 Hz²/Hz, corresponding to a 4 kHz linewidth. These figures describe the demonstrated device and operating conditions.

Integration trade-offs and future development

The fabrication sequence starts with Si3N4 waveguides on an oxidized silicon wafer. Silicon and then InP layers are bonded and processed above them, with oxide layers providing cladding and passivation. This wafer-bonded, backend integration approach shows how materials and optical functions can be combined without requiring a direct III-V-to-Si3N4 waveguide transition.

In the reported fabrication run, the spacer oxide was thinner than designed after planarization. This increased optical overlap with the via oxide and resulted in propagation loss of 0.43 dB/cm. The researchers identify lower loss as a route toward longer Si3N4 gratings, weaker grating coupling, or cascaded ring resonators—design options that could support further linewidth reduction and increased output power. Those improvements are prospective, not results established by this device.

For automation and industrial technology developers, the broader implication is architectural: active semiconductor gain and low-loss passive photonics need not be confined to separate chips or a single material platform. The demonstrated laser combines electrical pumping, a Si3N4-based cavity, improved temperature stability relative to the InP/Si comparison, and a narrow measured linewidth. Continued work on waveguide loss and integration could help extend this approach to photonic systems that require stable optical sources, including sensing and optical reference applications.

Access Official Technical PDF

About The Author