Access Official Technical PDF

Share Summary:LinkedInEmail

Time-resolved photoluminescence (TRPL) measures how light emitted by a material changes after a brief optical excitation. For semiconductor nanowires, the technique can help distinguish carrier recombination behavior that is difficult to infer from a steady-state spectrum alone. Measurements on wurtzite InP nanowires illustrate how both excitation power and sample structure can influence the observed emission and carrier lifetime.

The comparison is particularly relevant because wurtzite InP is a crystal structure that can occur in nanowires but is not found in bulk InP, which typically crystallizes in the zinc-blende structure. Surface states and crystallographic defects can affect recombination, making nanowire geometry and material quality important considerations when interpreting optical measurements.

Why measure carrier lifetime in wurtzite InP?

When a semiconductor absorbs light, it creates electrons and holes. These carriers relax toward available low-energy states in the conduction and valence bands. When an electron recombines with a hole, the process may emit a photon. The time carriers remain available before recombination is described by their recombination lifetime.

In wurtzite InP, the low-temperature band gap discussed in the study is approximately 1.49 eV. However, not all emitted light necessarily comes from direct band-to-band recombination. Defects can introduce states within the band gap, enabling lower-energy emission. Electrons and holes may also form excitons, bound states whose recombination produces emission distinct from the band-edge signal.

These different pathways matter in TRPL: a measured decay at a selected emission energy reflects the carriers and transitions contributing to that spectral region. A spectral feature below the band-gap energy may therefore have a different lifetime from band-edge emission.

How time-resolved photoluminescence works

In TRPL, a short light pulse generates electron-hole pairs, and the emitted photoluminescence is recorded as it evolves over time and wavelength. The experiment described used pulsed excitation from a Ti:sapphire laser and a synchroscan streak camera, with a reported time resolution of 800 femtoseconds. The samples were measured at low temperature, around 4 K.

A streak camera converts changes in the arrival time of light into a spatial pattern that can be recorded. In simplified terms, emitted photons are dispersed by wavelength and converted into photoelectrons at a photocathode. A rapidly changing electric field deflects the electrons according to their arrival time. After amplification, they strike a phosphor screen, where a camera records the resulting image. The image therefore captures both the spectral and temporal behavior of the emission.

For a lifetime measurement, the signal can be examined at a chosen emission energy and its intensity tracked over time. The decay provides information about the recombination dynamics, while spectra taken at different times can reveal whether the dominant emission energy shifts as carriers relax or recombine.

Excitation power and recombination dynamics

Carrier lifetime can depend on excitation level. Under low-level injection, the increase in carrier concentration is small relative to the equilibrium carrier populations. In the simplified radiative model presented, the lifetime is then independent of the number of photo-generated carriers. Under high-level injection, the carrier concentration becomes more influential, and the model predicts a shorter lifetime as excitation increases.

High excitation can also change the emission spectrum. When carrier density becomes sufficiently high, the Fermi level can move into a band, changing the energies of allowed transitions and broadening or shifting the photoluminescence peak. This behavior is associated with the Burstein-Moss effect. Consequently, measurements at different powers should be interpreted with both the spectral changes and the time-dependent decay in view.

Comparing short and long nanowires

The study compared two vapor-liquid-solid-grown wurtzite InP nanowire samples. The shorter sample was approximately 0.812 micrometers long and 0.085 micrometers in diameter. The longer sample was approximately 1.95 micrometers long and 0.141 micrometers in diameter. Both were grown from 30-nanometer gold particles, but their different growth times produced different dimensions and core-to-shell ratios.

At the band-edge emission near 1.49 eV, the reported lifetime behavior differed between samples:

  • Short nanowire: The measured lifetime increased from about 116.9 ps at low excitation power to about 248.9 ps at high power. This is opposite to the trend expected from the simplified high-injection model.
  • Long nanowire: The measured lifetime decreased from about 159.9 ps at low power to about 124.25 ps at high power, consistent with the expected direction described by that model.

The difference is a reminder that a theoretical trend does not by itself explain every measurement. In nanoscale structures, the observed decay can reflect multiple recombination pathways and sample-specific features. The short-wire result should therefore be treated as an observation requiring further interpretation, not as confirmation of the simple model.

Interpreting the lower-energy emission

A notable distinction was a feature near 1.45 eV in the long nanowire. It became more prominent at lower power or later times and was not observed in the short nanowire. Its presence was associated with a longer-lived contribution to the long-wire TRPL signal.

The study proposed that the feature could be related to impurities or shell-associated effects, given the difference in core-to-shell ratio. It also raised phosphorus vacancies and free-electron-to-neutral-acceptor recombination as possible explanations. These are hypotheses rather than established assignments. The reported absence of a sizeable redshift with decreasing power in steady-state photoluminescence was used to argue against attributing the feature to type-II transitions associated with stacking faults.

Practical implications for optical characterization

For engineers and researchers evaluating semiconductor nanowires, the results highlight several useful practices. Compare time-resolved data with steady-state photoluminescence, examine decay at specific emission energies, and record how spectra evolve with both time and excitation power. Differences in nanowire dimensions and core-to-shell structure should also be considered when comparing samples.

TRPL does not identify a defect or recombination mechanism on its own. Its value is in connecting the timing of emission to spectral features, helping determine which questions merit further structural or optical investigation. For wurtzite InP, the contrast between the two samples shows why lifetime measurements should be interpreted in the context of crystal structure, geometry, excitation conditions, and possible sub-band-gap emission.

Conclusion

Time-resolved photoluminescence provides a way to track carrier recombination in wurtzite InP nanowires across both time and wavelength. The measured power dependence differed between the short and long samples, while a lower-energy feature in the longer nanowire pointed to an additional recombination pathway that remains uncertain. For practical characterization, the key is to assess lifetime, spectral position, excitation power, and nanowire structure together rather than treating any single measurement as a complete explanation.

Access Official Technical PDF

About The Author