Access Official Technical PDF

Share Summary:LinkedInEmail

Mid-infrared laser diodes can provide compact, single-mode light sources for gas measurements in industrial environments. In the 1.6–2.1 μm wavelength range, gases including methane, hydrogen chloride, nitrous oxide, water vapor and carbon dioxide have characteristic absorption features. InP-based discrete-mode (DM) lasers use a modified ridge-waveguide design to select a single wavelength without the grating regrowth used in conventional distributed-feedback structures. This makes the technology relevant to engineers evaluating optical sources for tunable diode laser absorption spectroscopy (TDLAS) and other sensing systems.

Why use mid-infrared light for gas sensing?

TDLAS identifies gases by measuring how molecules absorb light at particular wavelengths. Molecular rotational-vibrational transitions create distinct absorption lines, or spectral fingerprints. A laser is tuned across a selected line by adjusting its drive current or temperature, and the resulting absorption can be used to detect a target gas.

The 1.6–2.1 μm region includes strong absorption bands for several gases of practical interest. Methane absorbs near 1.665 μm, hydrogen chloride near 1.743 μm, and nitrous oxide near 1.795 μm. Water vapor and carbon dioxide have prominent bands around 1.877 μm and 2.004 μm, respectively. Selecting a wavelength appropriate to the target gas is therefore central to designing a measurement system.

Compared with electrochemical point sensors, TDLAS can offer rapid response, long-term stability, selectivity and sensitivity, as well as the possibility of measurements over longer distances using open-path arrangements. The laser source is one part of the overall instrument; the measurement design must also account for the absorption feature and operating conditions relevant to the application.

Why InP is a practical laser platform

Mid-infrared diode lasers have been demonstrated using both indium phosphide (InP) and gallium antimonide (GaSb) material systems. InP is attractive for applications where chip cost matters because its processing methods, epitaxial growth and substrate supply benefit from technologies developed for telecommunications lasers. The source material also identifies substrate quality, cost and thermal performance as advantages of the InP platform.

To extend InP-based InGaAs emission toward longer wavelengths, the indium composition is increased, introducing compressive strain. Quantum wells can provide the active region, with strained barriers used to help manage the overall strain. Because quantum confinement shifts the bandgap compared with bulk material, the quantum-well composition and structure must be designed for the intended emission wavelength.

InP-based devices described in the 1.8–2.1 μm range demonstrate that this platform can support low-threshold operation and useful spectral performance. The broader development goal is to extend practical, lower-cost sources to wavelengths needed by additional sensing applications.

How a discrete-mode laser selects its wavelength

A DM laser begins with a ridge-waveguide Fabry-Pérot (FP) laser. In an ordinary FP cavity, multiple longitudinal modes may appear in the emission spectrum. The DM design modifies the cavity’s optical feedback by adding a series of shallow etched features, commonly called slots, along the ridge.

Each slot creates a small change in effective refractive index. At the boundary between slotted and unslotted sections, part of the propagating light is reflected. The combined reflections from appropriately positioned slots alter the cavity’s mirror-loss spectrum: the selected mode experiences lower mirror loss than competing modes, supporting single-wavelength operation.

The slots are etched into the ridge but do not reach the active waveguiding region. Their interaction with the optical mode is possible because the mode extends beyond the active layer into surrounding regions. Slot placement and spacing are therefore important design variables, alongside the laser’s cavity length and waveguide properties.

Unlike a buried-grating DFB structure, the DM approach adds etched features during processing of an otherwise conventional ridge-waveguide laser. It avoids grating overgrowth, reducing fabrication complexity. That distinction can be important when evaluating how a laser architecture may affect manufacturing and eventual source cost; it does not remove the need for precise waveguide and slot fabrication.

Performance demonstrated near the water-vapor band

A demonstrated InP DM device operating near 1.877 μm is relevant to water-vapor sensing. At a heat-sink temperature of 25°C, it produced a peak wavelength of 1877 nm and a side-mode suppression ratio (SMSR) of approximately 45 dB. SMSR compares the dominant lasing mode with unwanted side modes; a high value indicates that the main mode strongly dominates the measured spectrum.

The reported device operated continuously in a mode-hop-free manner from 15 to 55°C, with ex-facet optical output above 3 mW at 25°C. Its peak wavelength shifted with bias current at approximately 0.017 nm/mA and with temperature at approximately 0.113 nm/°C. These tuning characteristics matter in system design because changing current and temperature affects the laser wavelength, which must be aligned with the target gas absorption feature.

Across the described DM devices, single-mode operation with SMSR above 40 dB was reported over current and temperature variations. Changing the grating period also enabled wavelength selection across a broad gain range: devices based on the reported material achieved tunability spanning 1.75–2.1 μm, with a 120 nm range demonstrated for one wafer design. These are device results, not guarantees for every laser or sensing system.

Implications for industrial automation teams

For plant engineers, integrators and instrumentation teams, the practical value of a laser source depends on its fit with the measurement task. When assessing a TDLAS design, consider:

  • Target gas and wavelength: Match the laser’s operating range to a relevant absorption feature.
  • Temperature and current behavior: Account for wavelength tuning as drive current and device temperature change.
  • Spectral purity: Review SMSR and mode stability in relation to the measurement method.
  • Optical power and coupling: Distinguish ex-facet output from power delivered through the system’s optical path.
  • Integration requirements: Evaluate packaging, thermal control and the needs of point or open-path measurement arrangements.

In combustion monitoring, for example, water-vapor concentration can be related to process parameters such as combustion efficiency and heat release. The laser provides a wavelength-selective optical source; converting absorption into a dependable process measurement still requires appropriate instrument design and deployment.

Conclusion

InP-based mid-infrared laser diodes offer a route to compact single-mode sources for gas sensing across the 1.6–2.1 μm region. Discrete-mode lasers achieve wavelength selection through etched ridge features that shape cavity feedback, avoiding the grating regrowth required by some DFB designs. For industrial automation applications, the key is to match the laser’s wavelength, spectral behavior, tuning characteristics and output to the target gas and measurement architecture. These factors determine whether a promising diode technology can be effectively applied in a practical TDLAS instrument.

Access Official Technical PDF

About The Author