For engineers designing optical systems, laser output power is only part of the performance equation. A source may also need broad wavelength tunability, low frequency and intensity noise, and a compact, integrated architecture. A demonstrated hybrid integrated laser addresses these requirements by combining two semiconductor gain sections with one tunable optical cavity. The device delivered up to 85 mW at the fiber output while retaining a reported intrinsic linewidth of 320 Hz.
The design is relevant to applications including coherent communications, optical sensing and microwave photonics, where the stability and noise characteristics of the optical source can affect system performance. Its approach also offers a practical example of how active and passive photonic components can be combined to increase output power without giving up key laser characteristics.
Why combine two gain sections?
Hybrid integrated lasers bring together active semiconductor components and passive waveguides. In this device, indium phosphide (InP) reflective semiconductor optical amplifiers (RSOAs) provide optical gain, while a silicon nitride TriPleX platform forms the passive cavity. The waveguides have reported propagation losses below 0.1 dB/cm, supporting a low-loss optical path.
Earlier hybrid and heterogeneously integrated lasers could face power limitations in applications that require stronger optical output. The researchers addressed that constraint by coupling two individual RSOAs to a shared cavity rather than using one gain section. Each RSOA is 700 µm long and has its own electrical connection. The two sections therefore contribute gain to a common laser architecture, rather than operating as separate lasers.
The result is a dual-gain design intended to increase available output power while preserving the tuning behavior and spectral qualities associated with this type of laser. The reported output was twice that of devices with one RSOA and a similar cavity design.
How the tunable cavity works
The cavity uses a Vernier mirror arrangement based on two micro-resonators with slightly different lengths. Their free-spectral ranges are 208 GHz and 215 GHz. Because the resonators do not have identical spacing between their resonant frequencies, their combined response supports selection of the laser wavelength across a broader range than either resonator alone.
Control of the cavity and its outputs is built into the passive chip. Two thermo-optic tuners adjust the phases of the RSOAs within the cavity. Two tunable Mach-Zehnder couplers control output coupling and the optical power routed to the output waveguide. In practical terms, the design combines wavelength-selective cavity behavior with components that can adjust phase and output coupling.
The output waveguides connect to a fiber array using polarization-maintaining fibers. The reported coupling loss at this interface is 0.5 dB. The estimated coupling loss between the InP RSOAs and the TriPleX cavity is 1 dB, illustrating that optical interfaces are an important part of the overall hybrid assembly.
Output power, tuning and spectral quality
At a pump current of 250 mA for each RSOA, the laser produced 85 mW at the fiber output and 95 mW on-chip. These are distinct measurement points: the fiber figure includes the output coupling path, while the on-chip figure describes power before that fiber interface. The device maintained a tuning range from 1520 nm to 1580 nm and a side-mode suppression ratio (SMSR) greater than 50 dB.
SMSR describes the strength of the desired laser mode relative to unwanted side modes. A high value indicates that the selected mode dominates the output spectrum. Together, the reported tuning range and SMSR show that adding a second gain section did not prevent the laser from operating across the stated wavelength range with strong mode selection.
The output was limited by thermal conditions: above 250 mA per RSOA, the amplifiers saturated because of insufficient cooling. This is an important engineering consideration. Increasing available gain does not remove the need to manage heat in the active components, and thermal design can determine how much of the device’s potential output is usable.
Low linewidth and intensity noise
Frequency-noise measurements were used to estimate the laser’s intrinsic Lorentzian linewidth. With both gain sections driven at 100 mA and the heaters inactive, the measured white frequency-noise floor corresponded to an intrinsic linewidth of approximately 320 Hz. The heaters were left inactive for this measurement because noise from their drivers would otherwise affect the result.
The team also measured relative intensity noise (RIN) with a high-speed detector and electrical spectrum analyzer, covering frequencies up to 25 GHz. The reported laser RIN remained below -160 dBc/Hz across the measured range and reached approximately -170 dBc/Hz at most frequencies. The study also compared the laser’s RIN with relative system noise that included shot noise.
For microwave photonics, which processes radio-frequency signals through optical components, both frequency stability and intensity noise are relevant considerations. The measurements indicate that the dual-gain architecture can provide increased optical power while retaining low reported noise levels. They do not, by themselves, establish performance for every system configuration; integration and operating conditions still matter.
Practical implications for photonic system design
This hybrid integrated laser demonstrates a design strategy for applications that need a tunable, relatively high-power optical source without sacrificing narrow linewidth. For system integrators and technical decision-makers, the key points are:
- Shared-cavity gain: Two individually driven InP RSOAs contribute to one tunable cavity.
- Integrated wavelength and output control: Thermo-optic phase tuners and tunable Mach-Zehnder couplers manage cavity phase and output coupling.
- Power and noise together: The device reported 85 mW at the fiber output, a 320 Hz intrinsic linewidth and RIN below -160 dBc/Hz over the measured range.
- Thermal management remains essential: RSOA saturation above the stated drive current limited further output in this implementation.
The practical takeaway is that adding gain sections to a shared low-loss cavity can raise laser output while maintaining useful tuning and spectral characteristics. The demonstrated results make the architecture relevant to photonic systems where power, linewidth and noise must be considered together. Further output improvement was identified as a possibility through better RSOA thermal management or the addition of more gain units, although those approaches would require validation in future devices.